/* visual.c * File read and write routines for Visual Networks cap files. * Copyright (c) 2001, Tom Nisbet tnisbet@visualnetworks.com * * Wiretap Library * Copyright (c) 1998 by Gilbert Ramirez * * SPDX-License-Identifier: GPL-2.0-or-later */ #include "config.h" #include "visual.h" #include #include "wtap-int.h" #include "file_wrappers.h" /* * A Visual Networks traffic capture file contains three sections. The * first is a 192 octet file header. This is followed by the captured * packet header, and for ATM captures, there is an additional atm packet header. * The data follows the packet header. The last section is the packet index block. * The index block contains one 4 octet pointer for each captured packet. * The first packet index is (4 * num_pkts) octets from the end of the file * and the last index is in the last four octets of the file. * * All integer and time values are stored in little-endian format, except for * the ATM Packet Header, which is stored in network byte order. * * [ File Header ] * * * [ Packet Header 1 ] [(opt) ATM Packet Header] [ Data ] * ... * [ Packet Header n ] [(opt) ATM Packet Header] [ Data ] * * * [ Index Block 1 ] ... [ Index Block n ] */ /* Capture file header, INCLUDING the magic number, is 192 bytes. */ #define CAPTUREFILE_HEADER_SIZE 192 /* Magic number for Visual Networks traffic capture files. */ static const char visual_magic[] = { 5, 'V', 'N', 'F' }; /* Visual File Header (minus magic number). */ /* This structure is used to extract information */ struct visual_file_hdr { uint32_t num_pkts; /* Number of packets in the file */ uint32_t start_time; /* Capture start time in PC format */ uint16_t media_type; /* IANA ifType of packet source */ uint16_t max_length; /* Max allowable stored packet length */ uint16_t file_flags; /* File type flags */ /* Bit 0 indicates indexes present */ uint16_t file_version; /* Version number of this file format */ uint32_t media_speed; /* ifSpeed of packet source in bits/sec. */ uint16_t media_param; /* Media-specific extra parameter. */ char RESERVED_[102]; /* MUST BE ALL ZEROS FOR FUTURE COMPATIBILITY */ char description[64]; /* File description (null terminated) */ }; /* Packet status bits */ #define PS_LONG 0x01 #define PS_SHORT 0x02 #define PS_ERRORED 0x04 #define PS_1ST_AFTER_DROP 0x08 #define PS_APPROX_ORDER 0x10 #define PS_SENT 0x40 #define PS_ABORTED 0x80 /* Visual Packet Header */ /* This structure is used to extract information */ struct visual_pkt_hdr { uint32_t ts_delta; /* Time stamp - msecs since start of capture */ uint16_t orig_len; /* Actual length of packet */ uint16_t incl_len; /* Number of octets captured in file */ uint32_t status; /* Packet status flags (media specific) */ uint8_t encap_hint; /* Encapsulation type hint */ uint8_t encap_skip; /* Number of bytes to skip before decoding */ char RESERVED_[6]; /* RESERVED - must be zero */ }; /* Optional Visual ATM Packet Header */ /* This structure is used to extract information */ struct visual_atm_hdr { uint16_t vpi; /* 4 bits of zeros; 12 bits of ATM VPI */ uint16_t vci; /* ATM VCI */ uint8_t info; /* 4 bits version; 3 bits unused-zero; 1 bit direction */ uint8_t category; /* indicates type of traffic. 4 bits of status + 4 bits of type */ uint16_t cell_count; /* number of cells that make up this pdu */ uint32_t data_length; /* PDU data length for AAL-5 PDUs, all others - cellcount * 48 */ uint32_t ts_secs; /* seconds value of sysUpTime when the last cell of this PDU was captured */ uint32_t ts_nsec; /* nanoseconds value of sysUpTime when the last cell of this PDU was captured */ }; /* visual_atm_hdr info bit definitions */ #define FROM_NETWORK 0x01 #define ATM_VER_MASK 0xf0 /* Not currently displayed */ /* visual_atm_hdr category definitions */ /* High nibble - not currently displayed */ #define VN_INCOMPLETE 0x40 #define VN_BAD_CRC 0x80 #define VN_CAT_STAT_MASK 0xf0 /* Low nibble */ #define VN_UNKNOWN 0x00 #define VN_AAL1 0x01 #define VN_AAL2 0x02 #define VN_AAL34 0x03 #define VN_O191 0x04 #define VN_AAL5 0x05 #define VN_OAM 0x0a #define VN_RM 0x0b #define VN_IDLE 0x0c #define VN_CAT_TYPE_MASK 0x0f /* Additional information for reading Visual files */ struct visual_read_info { uint32_t num_pkts; /* Number of pkts in the file */ uint32_t current_pkt; /* Next packet to be read */ time_t start_time; /* Capture start time in seconds */ }; /* Additional information for writing Visual files */ struct visual_write_info { uint32_t start_time; /* Capture start time in seconds */ int index_table_index; /* Index of the next index entry */ int index_table_size; /* Allocated size of the index table */ uint32_t * index_table; /* File offsets for the packets */ uint32_t next_offset; /* Offset of next packet */ }; /* Local functions to handle file reads and writes */ static bool visual_read(wtap *wth, wtap_rec *rec, Buffer *buf, int *err, char **err_info, int64_t *data_offset); static bool visual_seek_read(wtap *wth, int64_t seek_off, wtap_rec *rec, Buffer *buf, int *err, char **err_info); static bool visual_read_packet(wtap *wth, FILE_T fh, wtap_rec *rec, Buffer *buf, int *err, char **err_info); static bool visual_dump(wtap_dumper *wdh, const wtap_rec *rec, const uint8_t *pd, int *err, char **err_info); static bool visual_dump_finish(wtap_dumper *wdh, int *err, char **err_info); static void visual_dump_free(wtap_dumper *wdh); static int visual_file_type_subtype = -1; void register_visual(void); /* Open a file for reading */ wtap_open_return_val visual_open(wtap *wth, int *err, char **err_info) { char magic[sizeof visual_magic]; struct visual_file_hdr vfile_hdr; struct visual_read_info * visual; int encap; /* Check the magic string at the start of the file */ if (!wtap_read_bytes(wth->fh, magic, sizeof magic, err, err_info)) { if (*err != WTAP_ERR_SHORT_READ) return WTAP_OPEN_ERROR; return WTAP_OPEN_NOT_MINE; } if (memcmp(magic, visual_magic, sizeof visual_magic) != 0) { return WTAP_OPEN_NOT_MINE; } /* Read the rest of the file header. */ if (!wtap_read_bytes(wth->fh, &vfile_hdr, sizeof vfile_hdr, err, err_info)) { return WTAP_OPEN_ERROR; } /* Verify the file version is known */ vfile_hdr.file_version = pletoh16(&vfile_hdr.file_version); if (vfile_hdr.file_version != 1) { *err = WTAP_ERR_UNSUPPORTED; *err_info = ws_strdup_printf("visual: file version %u unsupported", vfile_hdr.file_version); return WTAP_OPEN_ERROR; } /* Translate the encapsulation type; these values are SNMP ifType values, as found in https://www.iana.org/assignments/smi-numbers. Note that a file with media type 22 ("propPointToPointSerial") may contain Cisco HDLC or PPP over HDLC. This will get sorted out after the first packet is read. XXX - should we use WTAP_ENCAP_PER_PACKET for that? */ switch (pletoh16(&vfile_hdr.media_type)) { case 6: /* ethernet-csmacd */ encap = WTAP_ENCAP_ETHERNET; break; case 9: /* IEEE802.5 */ encap = WTAP_ENCAP_TOKEN_RING; break; case 16: /* lapb */ encap = WTAP_ENCAP_LAPB; break; case 22: /* propPointToPointSerial */ case 118: /* HDLC */ encap = WTAP_ENCAP_CHDLC_WITH_PHDR; break; case 32: /* frame-relay */ encap = WTAP_ENCAP_FRELAY_WITH_PHDR; break; case 37: /* ATM */ encap = WTAP_ENCAP_ATM_PDUS; break; default: *err = WTAP_ERR_UNSUPPORTED; *err_info = ws_strdup_printf("visual: network type %u unknown or unsupported", vfile_hdr.media_type); return WTAP_OPEN_ERROR; } /* Fill in the wiretap struct with data from the file header */ wth->file_type_subtype = visual_file_type_subtype; wth->file_encap = encap; wth->snapshot_length = pletoh16(&vfile_hdr.max_length); /* Set up the pointers to the handlers for this file type */ wth->subtype_read = visual_read; wth->subtype_seek_read = visual_seek_read; wth->file_tsprec = WTAP_TSPREC_MSEC; /* Add Visual-specific information to the wiretap struct for later use. */ visual = g_new(struct visual_read_info, 1); wth->priv = (void *)visual; visual->num_pkts = pletoh32(&vfile_hdr.num_pkts); visual->start_time = pletoh32(&vfile_hdr.start_time); visual->current_pkt = 1; /* * Add an IDB; we don't know how many interfaces were * involved, so we just say one interface, about which * we only know the link-layer type, snapshot length, * and time stamp resolution. */ wtap_add_generated_idb(wth); return WTAP_OPEN_MINE; } /* Read the next available packet from the file. This is called in a loop to sequentially read the entire file one time. After the file has been read once, any Future access to the packets is done through seek_read. */ static bool visual_read(wtap *wth, wtap_rec *rec, Buffer *buf, int *err, char **err_info, int64_t *data_offset) { struct visual_read_info *visual = (struct visual_read_info *)wth->priv; /* Check for the end of the packet data. Note that a check for file EOF will not work because there are index values stored after the last packet's data. */ if (visual->current_pkt > visual->num_pkts) { *err = 0; /* it's just an EOF, not an error */ return false; } visual->current_pkt++; *data_offset = file_tell(wth->fh); return visual_read_packet(wth, wth->fh, rec, buf, err, err_info); } /* Read packet header and data for random access. */ static bool visual_seek_read(wtap *wth, int64_t seek_off, wtap_rec *rec, Buffer *buf, int *err, char **err_info) { /* Seek to the packet header */ if (file_seek(wth->random_fh, seek_off, SEEK_SET, err) == -1) return false; /* Read the packet. */ if (!visual_read_packet(wth, wth->random_fh, rec, buf, err, err_info)) { if (*err == 0) *err = WTAP_ERR_SHORT_READ; return false; } return true; } static bool visual_read_packet(wtap *wth, FILE_T fh, wtap_rec *rec, Buffer *buf, int *err, char **err_info) { struct visual_read_info *visual = (struct visual_read_info *)wth->priv; struct visual_pkt_hdr vpkt_hdr; uint32_t packet_size; struct visual_atm_hdr vatm_hdr; uint32_t relmsecs; uint32_t packet_status; uint8_t *pd; /* Read the packet header. */ if (!wtap_read_bytes_or_eof(fh, &vpkt_hdr, (unsigned int)sizeof vpkt_hdr, err, err_info)) { return false; } /* Get the included length of data. This includes extra headers + payload */ packet_size = pletoh16(&vpkt_hdr.incl_len); rec->rec_type = REC_TYPE_PACKET; rec->block = wtap_block_create(WTAP_BLOCK_PACKET); rec->presence_flags = WTAP_HAS_TS|WTAP_HAS_CAP_LEN; /* Set the packet time and length. */ relmsecs = pletoh32(&vpkt_hdr.ts_delta); rec->ts.secs = visual->start_time + relmsecs/1000; rec->ts.nsecs = (relmsecs % 1000)*1000000; rec->rec_header.packet_header.len = pletoh16(&vpkt_hdr.orig_len); packet_status = pletoh32(&vpkt_hdr.status); /* Do encapsulation-specific processing. Most Visual capture types include the FCS in the original length value, but don't include the FCS as part of the payload or captured length. This is different from the model used in most other capture file formats, including pcap and pcapng in cases where the FCS isn't captured (which are the typical cases), and causes the RTP audio payload save to fail since then captured len != orig len. We adjust the original length to remove the FCS bytes we counted based on the file encapsualtion type. The only downside to this fix is throughput calculations will be slightly lower as it won't include the FCS bytes. However, as noted, that problem also exists with other capture formats. We also set status flags. The only status currently supported for all encapsulations is direction. This either goes in the p2p or the X.25 pseudo header. It would probably be better to move this up into the phdr. */ switch (wth->file_encap) { case WTAP_ENCAP_ETHERNET: /* Ethernet has a 4-byte FCS. */ if (rec->rec_header.packet_header.len < 4) { *err = WTAP_ERR_BAD_FILE; *err_info = ws_strdup_printf("visual: Ethernet packet has %u-byte original packet, less than the FCS length", rec->rec_header.packet_header.len); return false; } rec->rec_header.packet_header.len -= 4; /* XXX - the above implies that there's never an FCS; should this set the FCS length to 0? */ rec->rec_header.packet_header.pseudo_header.eth.fcs_len = -1; break; case WTAP_ENCAP_CHDLC_WITH_PHDR: /* This has a 2-byte FCS. */ if (rec->rec_header.packet_header.len < 2) { *err = WTAP_ERR_BAD_FILE; *err_info = ws_strdup_printf("visual: Cisco HDLC packet has %u-byte original packet, less than the FCS length", rec->rec_header.packet_header.len); return false; } rec->rec_header.packet_header.len -= 2; rec->rec_header.packet_header.pseudo_header.p2p.sent = (packet_status & PS_SENT) ? true : false; break; case WTAP_ENCAP_PPP_WITH_PHDR: /* No FCS. XXX - true? Note that PPP can negotiate no FCS, a 2-byte FCS, or a 4-byte FCS. */ rec->rec_header.packet_header.pseudo_header.p2p.sent = (packet_status & PS_SENT) ? true : false; break; case WTAP_ENCAP_FRELAY_WITH_PHDR: /* This has a 2-byte FCS. */ if (rec->rec_header.packet_header.len < 2) { *err = WTAP_ERR_BAD_FILE; *err_info = ws_strdup_printf("visual: Frame Relay packet has %u-byte original packet, less than the FCS length", rec->rec_header.packet_header.len); return false; } rec->rec_header.packet_header.len -= 2; rec->rec_header.packet_header.pseudo_header.dte_dce.flags = (packet_status & PS_SENT) ? 0x00 : FROM_DCE; break; case WTAP_ENCAP_LAPB: /* This has a 2-byte FCS. */ if (rec->rec_header.packet_header.len < 2) { *err = WTAP_ERR_BAD_FILE; *err_info = ws_strdup_printf("visual: Frame Relay packet has %u-byte original packet, less than the FCS length", rec->rec_header.packet_header.len); return false; } rec->rec_header.packet_header.len -= 2; rec->rec_header.packet_header.pseudo_header.dte_dce.flags = (packet_status & PS_SENT) ? 0x00 : FROM_DCE; break; case WTAP_ENCAP_ATM_PDUS: /* ATM original length doesn't include any FCS. Do nothing to the packet length. ATM packets have an additional packet header; read and process it. */ if (!wtap_read_bytes(fh, &vatm_hdr, (unsigned int)sizeof vatm_hdr, err, err_info)) { return false; } /* Remove ATM header from length of included bytes in capture, as this header was appended by the processor doing the packet reassembly, and was not transmitted across the wire */ packet_size -= (uint32_t)sizeof vatm_hdr; /* Set defaults */ rec->rec_header.packet_header.pseudo_header.atm.type = TRAF_UNKNOWN; rec->rec_header.packet_header.pseudo_header.atm.subtype = TRAF_ST_UNKNOWN; rec->rec_header.packet_header.pseudo_header.atm.aal5t_len = 0; /* Next two items not supported. Defaulting to zero */ rec->rec_header.packet_header.pseudo_header.atm.aal5t_u2u = 0; rec->rec_header.packet_header.pseudo_header.atm.aal5t_chksum = 0; /* Flags appear only to convey that packet is a raw cell. Set to 0 */ rec->rec_header.packet_header.pseudo_header.atm.flags = 0; /* Not supported. Defaulting to zero */ rec->rec_header.packet_header.pseudo_header.atm.aal2_cid = 0; switch(vatm_hdr.category & VN_CAT_TYPE_MASK ) { case VN_AAL1: rec->rec_header.packet_header.pseudo_header.atm.aal = AAL_1; break; case VN_AAL2: rec->rec_header.packet_header.pseudo_header.atm.aal = AAL_2; break; case VN_AAL34: rec->rec_header.packet_header.pseudo_header.atm.aal = AAL_3_4; break; case VN_AAL5: rec->rec_header.packet_header.pseudo_header.atm.aal = AAL_5; rec->rec_header.packet_header.pseudo_header.atm.type = TRAF_LLCMX; rec->rec_header.packet_header.pseudo_header.atm.aal5t_len = pntoh32(&vatm_hdr.data_length); break; case VN_OAM: /* Marking next 3 as OAM versus unknown */ case VN_O191: case VN_IDLE: case VN_RM: rec->rec_header.packet_header.pseudo_header.atm.aal = AAL_OAMCELL; break; case VN_UNKNOWN: default: rec->rec_header.packet_header.pseudo_header.atm.aal = AAL_UNKNOWN; break; } rec->rec_header.packet_header.pseudo_header.atm.vpi = pntoh16(&vatm_hdr.vpi) & 0x0FFF; rec->rec_header.packet_header.pseudo_header.atm.vci = pntoh16(&vatm_hdr.vci); rec->rec_header.packet_header.pseudo_header.atm.cells = pntoh16(&vatm_hdr.cell_count); /* Using bit value of 1 (DCE -> DTE) to indicate From Network */ rec->rec_header.packet_header.pseudo_header.atm.channel = vatm_hdr.info & FROM_NETWORK; break; /* Not sure about token ring. Just leaving alone for now. */ case WTAP_ENCAP_TOKEN_RING: default: break; } rec->rec_header.packet_header.caplen = packet_size; /* Check for too-large packet. */ if (packet_size > WTAP_MAX_PACKET_SIZE_STANDARD) { /* Probably a corrupt capture file; don't blow up trying to allocate space for an immensely-large packet. */ *err = WTAP_ERR_BAD_FILE; *err_info = ws_strdup_printf("visual: File has %u-byte packet, bigger than maximum of %u", packet_size, WTAP_MAX_PACKET_SIZE_STANDARD); return false; } /* Read the packet data */ if (!wtap_read_packet_bytes(fh, buf, packet_size, err, err_info)) return false; if (wth->file_encap == WTAP_ENCAP_CHDLC_WITH_PHDR) { /* Fill in the encapsulation. Visual files have a media type in the file header and an encapsulation type in each packet header. Files with a media type of HDLC can be either Cisco EtherType or PPP. The encapsulation hint values we've seen are: 2 - seen in an Ethernet capture 13 - seen in a PPP capture; possibly also seen in Cisco HDLC captures 14 - seen in a PPP capture; probably seen only for PPP. According to bug 2005, the collection probe can be configured for PPP, in which case the encapsulation hint is 14, or can be configured for auto-detect, in which case the encapsulation hint is 13, and the encapsulation must be guessed from the packet contents. Auto-detect is the default. */ pd = ws_buffer_start_ptr(buf); /* If PPP is specified in the encap hint, then use that */ if (vpkt_hdr.encap_hint == 14) { /* But first we need to examine the first three octets to try to determine the proper encapsulation, see RFC 2364. */ if (packet_size >= 3 && (0xfe == pd[0]) && (0xfe == pd[1]) && (0x03 == pd[2])) { /* It is actually LLC encapsulated PPP */ rec->rec_header.packet_header.pkt_encap = WTAP_ENCAP_ATM_RFC1483; } else { /* It is actually PPP */ rec->rec_header.packet_header.pkt_encap = WTAP_ENCAP_PPP_WITH_PHDR; } } else { /* Otherwise, we need to examine the first two octets to try to determine the encapsulation. */ if (packet_size >= 2 && (0xff == pd[0]) && (0x03 == pd[1])) { /* It is actually PPP */ rec->rec_header.packet_header.pkt_encap = WTAP_ENCAP_PPP_WITH_PHDR; } } } return true; } /* Check for media types that may be written in Visual file format. Returns 0 if the specified encapsulation type is supported, an error indication otherwise. */ static int visual_dump_can_write_encap(int encap) { /* Per-packet encapsulations aren't supported. */ if (encap == WTAP_ENCAP_PER_PACKET) return WTAP_ERR_ENCAP_PER_PACKET_UNSUPPORTED; /* Check for supported encapsulation types */ switch (encap) { case WTAP_ENCAP_ETHERNET: case WTAP_ENCAP_TOKEN_RING: case WTAP_ENCAP_LAPB: case WTAP_ENCAP_CHDLC_WITH_PHDR: case WTAP_ENCAP_FRELAY_WITH_PHDR: case WTAP_ENCAP_PPP: case WTAP_ENCAP_PPP_WITH_PHDR: return 0; } return WTAP_ERR_UNWRITABLE_ENCAP; } /* Open a file for writing. Returns true on success, false on failure; sets "*err" to an error code on failure */ static bool visual_dump_open(wtap_dumper *wdh, int *err, char **err_info _U_) { struct visual_write_info *visual; /* Set the write routines for a visual file. */ wdh->subtype_write = visual_dump; wdh->subtype_finish = visual_dump_finish; /* Create a struct to hold file information for the duration of the write */ visual = g_new(struct visual_write_info, 1); wdh->priv = (void *)visual; visual->index_table_index = 0; visual->index_table_size = 1024; visual->index_table = 0; visual->next_offset = CAPTUREFILE_HEADER_SIZE; /* All of the fields in the file header aren't known yet so just skip over it for now. It will be created after all of the packets have been written. */ if (wtap_dump_file_seek(wdh, CAPTUREFILE_HEADER_SIZE, SEEK_SET, err) == -1) return false; return true; } /* Write a packet to a Visual dump file. Returns true on success, false on failure. */ static bool visual_dump(wtap_dumper *wdh, const wtap_rec *rec, const uint8_t *pd, int *err, char **err_info _U_) { const union wtap_pseudo_header *pseudo_header = &rec->rec_header.packet_header.pseudo_header; struct visual_write_info * visual = (struct visual_write_info *)wdh->priv; struct visual_pkt_hdr vpkt_hdr = {0}; size_t hdr_size = sizeof vpkt_hdr; unsigned delta_msec; uint32_t packet_status; /* We can only write packet records. */ if (rec->rec_type != REC_TYPE_PACKET) { *err = WTAP_ERR_UNWRITABLE_REC_TYPE; return false; } /* * Make sure this packet doesn't have a link-layer type that * differs from the one for the file. */ if (wdh->file_encap != rec->rec_header.packet_header.pkt_encap) { *err = WTAP_ERR_ENCAP_PER_PACKET_UNSUPPORTED; return false; } /* Don't write anything we're not willing to read. */ if (rec->rec_header.packet_header.caplen > WTAP_MAX_PACKET_SIZE_STANDARD) { *err = WTAP_ERR_PACKET_TOO_LARGE; return false; } /* If the visual structure was never allocated then nothing useful can be done. */ if (visual == 0) return false; /* Visual UpTime capture files have a capture start time in the file header. Each packet has a capture time (in msec) relative to the file start time. Use the time of the first packet as the file start time. */ if (visual->index_table_index == 0) { /* * This is the first packet. Save its start time as the file time. * * XXX - is the start time signed, or unsigned? If it's signed, * in which case we should check against INT32_MIN and INT32_MAX * and make start_time a int32_t. */ if (rec->ts.secs < 0 || rec->ts.secs > WTAP_NSTIME_32BIT_SECS_MAX) { *err = WTAP_ERR_TIME_STAMP_NOT_SUPPORTED; return false; } visual->start_time = (uint32_t)rec->ts.secs; /* Initialize the index table */ visual->index_table = (uint32_t *)g_malloc(1024 * sizeof *visual->index_table); visual->index_table_size = 1024; } /* Calculate milliseconds since capture start. */ delta_msec = rec->ts.nsecs / 1000000; delta_msec += (uint32_t)((rec->ts.secs - visual->start_time) * 1000); vpkt_hdr.ts_delta = GUINT32_TO_LE(delta_msec); /* Fill in the length fields. */ vpkt_hdr.orig_len = GUINT16_TO_LE(rec->rec_header.packet_header.len); vpkt_hdr.incl_len = GUINT16_TO_LE(rec->rec_header.packet_header.caplen); /* Fill in the encapsulation hint for the file's media type. */ switch (wdh->file_encap) { case WTAP_ENCAP_ETHERNET: /* Ethernet */ vpkt_hdr.encap_hint = 2; break; case WTAP_ENCAP_TOKEN_RING: /* Token Ring */ vpkt_hdr.encap_hint = 3; break; case WTAP_ENCAP_PPP: /* PPP */ case WTAP_ENCAP_PPP_WITH_PHDR: vpkt_hdr.encap_hint = 14; break; case WTAP_ENCAP_CHDLC_WITH_PHDR: /* HDLC Router */ vpkt_hdr.encap_hint = 13; break; case WTAP_ENCAP_FRELAY_WITH_PHDR: /* Frame Relay Auto-detect */ vpkt_hdr.encap_hint = 12; break; case WTAP_ENCAP_LAPB: /* Unknown */ default: vpkt_hdr.encap_hint = 1; break; } /* Set status flags. The only status currently supported for all encapsulations is direction. This either goes in the p2p or the X.25 pseudo header. It would probably be better to move this up into the phdr. */ packet_status = 0; switch (wdh->file_encap) { case WTAP_ENCAP_CHDLC_WITH_PHDR: packet_status |= (pseudo_header->p2p.sent ? PS_SENT : 0x00); break; case WTAP_ENCAP_FRELAY_WITH_PHDR: case WTAP_ENCAP_LAPB: packet_status |= ((pseudo_header->dte_dce.flags & FROM_DCE) ? 0x00 : PS_SENT); break; } vpkt_hdr.status = GUINT32_TO_LE(packet_status); /* Write the packet header. */ if (!wtap_dump_file_write(wdh, &vpkt_hdr, hdr_size, err)) return false; /* Write the packet data */ if (!wtap_dump_file_write(wdh, pd, rec->rec_header.packet_header.caplen, err)) return false; /* Store the frame offset in the index table. */ if (visual->index_table_index >= visual->index_table_size) { /* End of table reached. Reallocate with a larger size */ visual->index_table_size *= 2; visual->index_table = (uint32_t *)g_realloc(visual->index_table, visual->index_table_size * sizeof *visual->index_table); } visual->index_table[visual->index_table_index] = GUINT32_TO_LE(visual->next_offset); /* Update the table index and offset for the next frame. */ visual->index_table_index++; visual->next_offset += (uint32_t) hdr_size + rec->rec_header.packet_header.caplen; return true; } /* Finish writing to a dump file. Returns true on success, false on failure. */ static bool visual_dump_finish(wtap_dumper *wdh, int *err, char **err_info _U_) { struct visual_write_info * visual = (struct visual_write_info *)wdh->priv; size_t n_to_write; struct visual_file_hdr vfile_hdr = {0}; const char *magicp; size_t magic_size; /* If the visual structure was never allocated then nothing useful can be done. */ if (visual == 0) return false; /* Write out the frame table at the end of the file. */ if (visual->index_table) { /* Write the index table to the file. */ n_to_write = visual->index_table_index * sizeof *visual->index_table; if (!wtap_dump_file_write(wdh, visual->index_table, n_to_write, err)) { visual_dump_free(wdh); return false; } } /* Write the magic number at the start of the file. */ if (wtap_dump_file_seek(wdh, 0, SEEK_SET, err) == -1) return false; magicp = visual_magic; magic_size = sizeof visual_magic; if (!wtap_dump_file_write(wdh, magicp, magic_size, err)) { visual_dump_free(wdh); return false; } vfile_hdr.num_pkts = GUINT32_TO_LE(visual->index_table_index); vfile_hdr.start_time = GUINT32_TO_LE(visual->start_time); vfile_hdr.max_length = GUINT16_TO_LE(65535); vfile_hdr.file_flags = GUINT16_TO_LE(1); /* indexes are present */ vfile_hdr.file_version = GUINT16_TO_LE(1); (void) g_strlcpy(vfile_hdr.description, "Wireshark file", 64); /* Translate the encapsulation type */ switch (wdh->file_encap) { case WTAP_ENCAP_ETHERNET: vfile_hdr.media_type = GUINT16_TO_LE(6); break; case WTAP_ENCAP_TOKEN_RING: vfile_hdr.media_type = GUINT16_TO_LE(9); break; case WTAP_ENCAP_LAPB: vfile_hdr.media_type = GUINT16_TO_LE(16); break; case WTAP_ENCAP_PPP: /* PPP is differentiated from CHDLC in PktHdr */ case WTAP_ENCAP_PPP_WITH_PHDR: case WTAP_ENCAP_CHDLC_WITH_PHDR: vfile_hdr.media_type = GUINT16_TO_LE(22); break; case WTAP_ENCAP_FRELAY_WITH_PHDR: vfile_hdr.media_type = GUINT16_TO_LE(32); break; } /* Write the file header following the magic bytes. */ if (!wtap_dump_file_write(wdh, &vfile_hdr, sizeof vfile_hdr, err)) { visual_dump_free(wdh); return false; } /* Deallocate the file write data */ visual_dump_free(wdh); return true; } /* Free the memory allocated by a visual file writer. */ static void visual_dump_free(wtap_dumper *wdh) { struct visual_write_info * visual = (struct visual_write_info *)wdh->priv; if (visual) { /* Free the index table memory. */ g_free(visual->index_table); } } static const struct supported_block_type visual_blocks_supported[] = { /* * We support packet blocks, with no comments or other options. */ { WTAP_BLOCK_PACKET, MULTIPLE_BLOCKS_SUPPORTED, NO_OPTIONS_SUPPORTED } }; static const struct file_type_subtype_info visual_info = { "Visual Networks traffic capture", "visual", NULL, NULL, true, BLOCKS_SUPPORTED(visual_blocks_supported), visual_dump_can_write_encap, visual_dump_open, NULL }; void register_visual(void) { visual_file_type_subtype = wtap_register_file_type_subtype(&visual_info); /* * Register name for backwards compatibility with the * wtap_filetypes table in Lua. */ wtap_register_backwards_compatibility_lua_name("VISUAL_NETWORKS", visual_file_type_subtype); } /* * Editor modelines - https://www.wireshark.org/tools/modelines.html * * Local variables: * c-basic-offset: 4 * tab-width: 8 * indent-tabs-mode: nil * End: * * vi: set shiftwidth=4 tabstop=8 expandtab: * :indentSize=4:tabSize=8:noTabs=true: */