// SPDX-License-Identifier: (GPL-2.0-only OR MIT) /* * Copyright 2024 NXP */ /dts-v1/; #include #include "imx93.dtsi" / { model = "NXP i.MX93 9x9 Quick Start Board"; compatible = "fsl,imx93-9x9-qsb", "fsl,imx93"; bt_sco_codec: bt-sco-codec { #sound-dai-cells = <1>; compatible = "linux,bt-sco"; }; chosen { stdout-path = &lpuart1; }; reserved-memory { #address-cells = <2>; #size-cells = <2>; ranges; linux,cma { compatible = "shared-dma-pool"; reusable; size = <0 0x10000000>; linux,cma-default; }; vdev0vring0: vdev0vring0@a4000000 { reg = <0 0xa4000000 0 0x8000>; no-map; }; vdev0vring1: vdev0vring1@a4008000 { reg = <0 0xa4008000 0 0x8000>; no-map; }; vdev1vring0: vdev1vring0@a4010000 { reg = <0 0xa4010000 0 0x8000>; no-map; }; vdev1vring1: vdev1vring1@a4018000 { reg = <0 0xa4018000 0 0x8000>; no-map; }; rsc_table: rsc-table@2021e000 { reg = <0 0x2021e000 0 0x1000>; no-map; }; vdevbuffer: vdevbuffer@a4020000 { compatible = "shared-dma-pool"; reg = <0 0xa4020000 0 0x100000>; no-map; }; }; reg_vref_1v8: regulator-adc-vref { compatible = "regulator-fixed"; regulator-name = "VREF_1V8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; reg_audio_pwr: regulator-audio-pwr { compatible = "regulator-fixed"; regulator-name = "audio-pwr"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&pcal6524 16 GPIO_ACTIVE_HIGH>; enable-active-high; }; reg_rpi_3v3: regulator-rpi { compatible = "regulator-fixed"; regulator-name = "VDD_RPI_3V3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&pcal6524 21 GPIO_ACTIVE_HIGH>; enable-active-high; }; reg_usdhc2_vmmc: regulator-usdhc2 { compatible = "regulator-fixed"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; regulator-name = "VSD_3V3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>; enable-active-high; off-on-delay-us = <12000>; }; sound-bt-sco { compatible = "simple-audio-card"; simple-audio-card,name = "bt-sco-audio"; simple-audio-card,format = "dsp_a"; simple-audio-card,bitclock-inversion; simple-audio-card,frame-master = <&btcpu>; simple-audio-card,bitclock-master = <&btcpu>; btcpu: simple-audio-card,cpu { sound-dai = <&sai1>; dai-tdm-slot-num = <2>; dai-tdm-slot-width = <16>; }; simple-audio-card,codec { sound-dai = <&bt_sco_codec 1>; }; }; sound-micfil { compatible = "fsl,imx-audio-card"; model = "micfil-audio"; pri-dai-link { link-name = "micfil hifi"; format = "i2s"; cpu { sound-dai = <&micfil>; }; }; }; sound-wm8962 { compatible = "fsl,imx-audio-wm8962"; model = "wm8962-audio"; audio-cpu = <&sai3>; audio-codec = <&wm8962>; hp-det-gpio = <&pcal6524 4 GPIO_ACTIVE_HIGH>; audio-routing = "Headphone Jack", "HPOUTL", "Headphone Jack", "HPOUTR", "Ext Spk", "SPKOUTL", "Ext Spk", "SPKOUTR", "AMIC", "MICBIAS", "IN3R", "AMIC", "IN1R", "AMIC"; }; }; &adc1 { vref-supply = <®_vref_1v8>; status = "okay"; }; &cm33 { mbox-names = "tx", "rx", "rxdb"; mboxes = <&mu1 0 1>, <&mu1 1 1>, <&mu1 3 1>; memory-region = <&vdevbuffer>, <&vdev0vring0>, <&vdev0vring1>, <&vdev1vring0>, <&vdev1vring1>, <&rsc_table>; status = "okay"; }; &eqos { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_eqos>; phy-mode = "rgmii-id"; phy-handle = <ðphy1>; status = "okay"; mdio { compatible = "snps,dwmac-mdio"; #address-cells = <1>; #size-cells = <0>; clock-frequency = <5000000>; ethphy1: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <1>; eee-broken-1000t; reset-gpios = <&pcal6524 15 GPIO_ACTIVE_LOW>; reset-assert-us = <10000>; reset-deassert-us = <80000>; realtek,clkout-disable; }; }; }; &lpi2c1 { clock-frequency = <400000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpi2c1>; status = "okay"; wm8962: audio-codec@1a { compatible = "wlf,wm8962"; reg = <0x1a>; clocks = <&clk IMX93_CLK_SAI3_GATE>; DCVDD-supply = <®_audio_pwr>; DBVDD-supply = <®_audio_pwr>; AVDD-supply = <®_audio_pwr>; CPVDD-supply = <®_audio_pwr>; MICVDD-supply = <®_audio_pwr>; PLLVDD-supply = <®_audio_pwr>; SPKVDD1-supply = <®_audio_pwr>; SPKVDD2-supply = <®_audio_pwr>; gpio-cfg = < 0x0000 /* 0:Default */ 0x0000 /* 1:Default */ 0x0000 /* 2:FN_DMICCLK */ 0x0000 /* 3:Default */ 0x0000 /* 4:FN_DMICCDAT */ 0x0000 /* 5:Default */ >; }; ptn5110: tcpc@50 { compatible = "nxp,ptn5110", "tcpci"; reg = <0x50>; interrupt-parent = <&gpio3>; interrupts = <26 IRQ_TYPE_LEVEL_LOW>; typec1_con: connector { compatible = "usb-c-connector"; label = "USB-C"; power-role = "dual"; data-role = "dual"; try-power-role = "sink"; source-pdos = ; sink-pdos = ; op-sink-microwatt = <15000000>; self-powered; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; typec1_dr_sw: endpoint { remote-endpoint = <&usb1_drd_sw>; }; }; }; }; }; rtc@53 { compatible = "nxp,pcf2131"; reg = <0x53>; interrupt-parent = <&pcal6524>; interrupts = <1 IRQ_TYPE_EDGE_FALLING>; }; }; &lpi2c2 { clock-frequency = <400000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpi2c2>; status = "okay"; pcal6524: gpio@22 { compatible = "nxp,pcal6524"; reg = <0x22>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; interrupt-parent = <&gpio3>; interrupts = <26 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcal6524>; exp-sel-hog { gpio-hog; gpios = <22 GPIO_ACTIVE_HIGH>; output-low; }; mic-can-sel-hog { gpio-hog; gpios = <17 GPIO_ACTIVE_HIGH>; output-low; }; }; pmic@25 { compatible = "nxp,pca9451a"; reg = <0x25>; interrupt-parent = <&pcal6524>; interrupts = <11 IRQ_TYPE_EDGE_FALLING>; regulators { buck1: BUCK1 { regulator-name = "BUCK1"; regulator-min-microvolt = <650000>; regulator-max-microvolt = <2237500>; regulator-boot-on; regulator-always-on; regulator-ramp-delay = <3125>; }; buck2: BUCK2 { regulator-name = "BUCK2"; regulator-min-microvolt = <600000>; regulator-max-microvolt = <2187500>; regulator-boot-on; regulator-always-on; regulator-ramp-delay = <3125>; }; buck4: BUCK4 { regulator-name = "BUCK4"; regulator-min-microvolt = <600000>; regulator-max-microvolt = <3400000>; regulator-boot-on; regulator-always-on; }; buck5: BUCK5 { regulator-name = "BUCK5"; regulator-min-microvolt = <600000>; regulator-max-microvolt = <3400000>; regulator-boot-on; regulator-always-on; }; buck6: BUCK6 { regulator-name = "BUCK6"; regulator-min-microvolt = <600000>; regulator-max-microvolt = <3400000>; regulator-boot-on; regulator-always-on; }; ldo1: LDO1 { regulator-name = "LDO1"; regulator-min-microvolt = <1600000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; ldo4: LDO4 { regulator-name = "LDO4"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; ldo5: LDO5 { regulator-name = "LDO5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; }; }; }; &lpuart1 { /* console */ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; &micfil { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pdm>; assigned-clocks = <&clk IMX93_CLK_PDM>; assigned-clock-parents = <&clk IMX93_CLK_AUDIO_PLL>; assigned-clock-rates = <49152000>; status = "okay"; }; &mu1 { status = "okay"; }; &mu2 { status = "okay"; }; &sai1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai1>; assigned-clocks = <&clk IMX93_CLK_SAI1>; assigned-clock-parents = <&clk IMX93_CLK_AUDIO_PLL>; assigned-clock-rates = <12288000>; fsl,sai-mclk-direction-output; status = "okay"; }; &sai3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai3>; assigned-clocks = <&clk IMX93_CLK_SAI3>; assigned-clock-parents = <&clk IMX93_CLK_AUDIO_PLL>; assigned-clock-rates = <12288000>; fsl,sai-mclk-direction-output; fsl,sai-synchronous-rx; status = "okay"; }; &usbotg1 { dr_mode = "otg"; hnp-disable; srp-disable; adp-disable; usb-role-switch; disable-over-current; samsung,picophy-pre-emp-curr-control = <3>; samsung,picophy-dc-vol-level-adjust = <7>; status = "okay"; port { usb1_drd_sw: endpoint { remote-endpoint = <&typec1_dr_sw>; }; }; }; &usdhc1 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc1>; pinctrl-1 = <&pinctrl_usdhc1_100mhz>; pinctrl-2 = <&pinctrl_usdhc1_200mhz>; bus-width = <8>; non-removable; status = "okay"; }; &usdhc2 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; vmmc-supply = <®_usdhc2_vmmc>; bus-width = <4>; no-mmc; status = "okay"; }; &wdog3 { status = "okay"; }; &iomuxc { pinctrl_eqos: eqosgrp { fsl,pins = < MX93_PAD_ENET1_MDC__ENET_QOS_MDC 0x57e MX93_PAD_ENET1_MDIO__ENET_QOS_MDIO 0x57e MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0 0x57e MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1 0x57e MX93_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2 0x57e MX93_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3 0x57e MX93_PAD_ENET1_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x58e MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x57e MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0 0x57e MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1 0x57e MX93_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2 0x57e MX93_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3 0x57e MX93_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x58e MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x57e >; }; pinctrl_lpi2c1: lpi2c1grp { fsl,pins = < MX93_PAD_I2C1_SCL__LPI2C1_SCL 0x40000b9e MX93_PAD_I2C1_SDA__LPI2C1_SDA 0x40000b9e >; }; pinctrl_lpi2c2: lpi2c2grp { fsl,pins = < MX93_PAD_I2C2_SCL__LPI2C2_SCL 0x40000b9e MX93_PAD_I2C2_SDA__LPI2C2_SDA 0x40000b9e >; }; pinctrl_pcal6524: pcal6524grp { fsl,pins = < MX93_PAD_CCM_CLKO1__GPIO3_IO26 0x31e >; }; pinctrl_pdm: pdmgrp { fsl,pins = < MX93_PAD_PDM_CLK__PDM_CLK 0x31e MX93_PAD_PDM_BIT_STREAM0__PDM_BIT_STREAM00 0x31e MX93_PAD_PDM_BIT_STREAM1__PDM_BIT_STREAM01 0x31e >; }; pinctrl_uart1: uart1grp { fsl,pins = < MX93_PAD_UART1_RXD__LPUART1_RX 0x31e MX93_PAD_UART1_TXD__LPUART1_TX 0x31e >; }; pinctrl_uart5: uart5grp { fsl,pins = < MX93_PAD_DAP_TDO_TRACESWO__LPUART5_TX 0x31e MX93_PAD_DAP_TDI__LPUART5_RX 0x31e MX93_PAD_DAP_TMS_SWDIO__LPUART5_RTS_B 0x31e MX93_PAD_DAP_TCLK_SWCLK__LPUART5_CTS_B 0x31e >; }; /* need to config the SION for data and cmd pad, refer to ERR052021 */ pinctrl_usdhc1: usdhc1grp { fsl,pins = < MX93_PAD_SD1_CLK__USDHC1_CLK 0x1582 MX93_PAD_SD1_CMD__USDHC1_CMD 0x40001382 MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x40001382 MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x40001382 MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x40001382 MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x40001382 MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x40001382 MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x40001382 MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x40001382 MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x40001382 MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x1582 >; }; /* need to config the SION for data and cmd pad, refer to ERR052021 */ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { fsl,pins = < MX93_PAD_SD1_CLK__USDHC1_CLK 0x158e MX93_PAD_SD1_CMD__USDHC1_CMD 0x4000138e MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x4000138e MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x4000138e MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x4000138e MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x4000138e MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x4000138e MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x4000138e MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x4000138e MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x4000138e MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x158e >; }; /* need to config the SION for data and cmd pad, refer to ERR052021 */ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { fsl,pins = < MX93_PAD_SD1_CLK__USDHC1_CLK 0x15fe MX93_PAD_SD1_CMD__USDHC1_CMD 0x400013fe MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x400013fe MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x400013fe MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x400013fe MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x400013fe MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x400013fe MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x400013fe MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x400013fe MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x400013fe MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x15fe >; }; pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { fsl,pins = < MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e >; }; pinctrl_sai1: sai1grp { fsl,pins = < MX93_PAD_SAI1_TXC__SAI1_TX_BCLK 0x31e MX93_PAD_SAI1_TXFS__SAI1_TX_SYNC 0x31e MX93_PAD_SAI1_TXD0__SAI1_TX_DATA00 0x31e MX93_PAD_SAI1_RXD0__SAI1_RX_DATA00 0x31e >; }; pinctrl_sai3: sai3grp { fsl,pins = < MX93_PAD_GPIO_IO12__SAI3_RX_SYNC 0x31e MX93_PAD_GPIO_IO18__SAI3_RX_BCLK 0x31e MX93_PAD_GPIO_IO17__SAI3_MCLK 0x31e MX93_PAD_GPIO_IO19__SAI3_TX_DATA00 0x31e MX93_PAD_GPIO_IO20__SAI3_RX_DATA00 0x31e >; }; pinctrl_usdhc2_gpio: usdhc2gpiogrp { fsl,pins = < MX93_PAD_SD2_CD_B__GPIO3_IO00 0x31e >; }; /* need to config the SION for data and cmd pad, refer to ERR052021 */ pinctrl_usdhc2: usdhc2grp { fsl,pins = < MX93_PAD_SD2_CLK__USDHC2_CLK 0x1582 MX93_PAD_SD2_CMD__USDHC2_CMD 0x40001382 MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x40001382 MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x40001382 MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x40001382 MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x40001382 MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e >; }; /* need to config the SION for data and cmd pad, refer to ERR052021 */ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { fsl,pins = < MX93_PAD_SD2_CLK__USDHC2_CLK 0x158e MX93_PAD_SD2_CMD__USDHC2_CMD 0x4000138e MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x4000138e MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x4000138e MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x4000138e MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x4000138e MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e >; }; /* need to config the SION for data and cmd pad, refer to ERR052021 */ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { fsl,pins = < MX93_PAD_SD2_CLK__USDHC2_CLK 0x15fe MX93_PAD_SD2_CMD__USDHC2_CMD 0x400013fe MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x400013fe MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x400013fe MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x400013fe MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x400013fe MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e >; }; };