// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Google Homestar board device tree source * * Copyright 2021 Google LLC. */ #include "sc7180-trogdor-rt5682i-sku.dtsi" #include "sc7180-trogdor-detachable.dtsi" / { /* BOARD-SPECIFIC TOP LEVEL NODES */ max98360a_1: amplifier-1 { compatible = "maxim,max98360a"; #sound-dai-cells = <0>; }; max98360a_2: amplifier-2 { compatible = "maxim,max98360a"; #sound-dai-cells = <0>; }; max98360a_3: amplifier-3 { compatible = "maxim,max98360a"; #sound-dai-cells = <0>; }; pp3300_touch: pp3300-touch-regulator { compatible = "regulator-fixed"; regulator-name = "pp3300_touch"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>; enable-active-high; pinctrl-names = "default"; pinctrl-0 = <&en_pp3300_touch>; vin-supply = <&pp3300_a>; }; thermal-zones { skin_temp_thermal: skin-temp-thermal { polling-delay-passive = <250>; thermal-sensors = <&pm6150_adc_tm 1>; sustainable-power = <965>; trips { skin_temp_alert0: trip-point0 { temperature = <55000>; hysteresis = <1000>; type = "passive"; }; skin_temp_alert1: trip-point1 { temperature = <58000>; hysteresis = <1000>; type = "passive"; }; skin-temp-crit { temperature = <73000>; hysteresis = <1000>; type = "critical"; }; }; cooling-maps { map0 { trip = <&skin_temp_alert0>; cooling-device = <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; map1 { trip = <&skin_temp_alert1>; cooling-device = <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; }; }; }; /* * ADDITIONS TO FIXED REGULATORS DEFINED IN PARENT DEVICE TREE FILES * * Sort order matches the order in the parent files (parents before children). */ &pp3300_dx_edp { /* * The atna33xc20 really likes to be power cycled to keep it from * getting in a bad state. This is the reason that the touchscreen * rail and eDP rails are separate from each other on homestar (but * not other trogdor devices) Make sure it starts "off" at bootup. */ /delete-property/ regulator-boot-on; }; /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */ ap_ts_pen_1v8: &i2c4 { status = "okay"; clock-frequency = <400000>; ap_ts: touchscreen@14 { compatible = "goodix,gt7375p"; reg = <0x14>; pinctrl-names = "default"; pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; interrupt-parent = <&tlmm>; interrupts = <9 IRQ_TYPE_LEVEL_LOW>; panel = <&panel>; reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; vdd-supply = <&pp3300_touch>; }; }; /* Panel controls backlight over aux channel */ &backlight { status = "disabled"; }; &camcc { status = "okay"; }; &panel { compatible = "samsung,atna33xc20"; enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; /delete-property/ backlight; }; &pm6150_adc { channel@4d { reg = ; qcom,ratiometric; qcom,hw-settle-time = <200>; label = "skin_therm"; }; }; &pm6150_adc_tm { status = "okay"; skin-temp-thermistor@1 { reg = <1>; io-channels = <&pm6150_adc ADC5_AMUX_THM1_100K_PU>; qcom,ratiometric; qcom,hw-settle-time-us = <200>; }; }; &pp1800_uf_cam { status = "okay"; }; &pp1800_wf_cam { status = "okay"; }; &pp2800_uf_cam { status = "okay"; }; &pp2800_wf_cam { status = "okay"; }; &pp3300_dx_edp { gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>; }; &secondary_mi2s { qcom,playback-sd-lines = <0 1>; }; &sound_multimedia1_codec { sound-dai = <&max98360a>, <&max98360a_1>, <&max98360a_2>, <&max98360a_3> ; }; &wifi { qcom,ath10k-calibration-variant = "GO_HOMESTAR"; }; /* PINCTRL - modifications to sc7180-trogdor.dtsi */ &en_pp3300_dx_edp { pins = "gpio67"; }; &sec_mi2s_active { pins = "gpio49", "gpio50", "gpio51", "gpio52"; }; &ts_reset_l { /* * We want reset state by default and it will be up to the * driver to disable this when it's ready. */ output-low; }; /* PINCTRL - board-specific pinctrl */ &tlmm { gpio-line-names = "HUB_RST_L", "AP_RAM_ID0", "AP_SKU_ID2", "AP_RAM_ID1", "", "AP_RAM_ID2", "UF_CAM_EN", "WF_CAM_EN", "TS_RESET_L", "TS_INT_L", "", "EDP_BRIJ_IRQ", "AP_EDP_BKLTEN", "UF_CAM_MCLK", "WF_CAM_CLK", "EDP_BRIJ_I2C_SDA", "EDP_BRIJ_I2C_SCL", "UF_CAM_SDA", "UF_CAM_SCL", "WF_CAM_SDA", "WF_CAM_SCL", "AVEE_LCD_EN", "", "AMP_EN", "AMP_EN2", "AP_SAR_SENSOR_SDA", "AP_SAR_SENSOR_SCL", "SEL_LCM", "HP_IRQ", "WF_CAM_RST_L", "UF_CAM_RST_L", "AP_BRD_ID2", "BRIJ_SUSPEND", "AP_BRD_ID0", "AP_H1_SPI_MISO", "AP_H1_SPI_MOSI", "AP_H1_SPI_CLK", "AP_H1_SPI_CS_L", "BT_UART_CTS", "BT_UART_RTS", "BT_UART_TXD", "BT_UART_RXD", "H1_AP_INT_ODL", "", "UART_AP_TX_DBG_RX", "UART_DBG_TX_AP_RX", "HP_I2C_SDA", "HP_I2C_SCL", "FORCED_USB_BOOT", "AMP_BCLK", "AMP_LRCLK", "AMP_DIN", "AMP_DIN_2", "HP_BCLK", "HP_LRCLK", "HP_DOUT", "HP_DIN", "HP_MCLK", "AP_SKU_ID0", "AP_EC_SPI_MISO", "AP_EC_SPI_MOSI", "AP_EC_SPI_CLK", "AP_EC_SPI_CS_L", "AP_SPI_CLK", "AP_SPI_MOSI", "AP_SPI_MISO", /* * AP_FLASH_WP_L is crossystem ABI. Schematics * call it BIOS_FLASH_WP_L. */ "AP_FLASH_WP_L", "EN_PP3300_DX_EDP", "AP_SPI_CS0_L", "SD_CD_ODL", "", "", "", "WLAN_SW_CTRL", "", "REPORT_E", "VDD_RESET_1.8V", "ID0", "", "ID1", "AVDD_LCD_EN", "MIPI_1.8V_EN", "", "CODEC_PWR_EN", "HUB_EN", "", "PP1800_MIPI_SW_EN", "EN_PP3300_TOUCH", "", "", "AP_SKU_ID1", "AP_RST_REQ", "", "AP_BRD_ID1", "AP_EC_INT_L", "SDM_GRFC_3", "", "", "BOOT_CONFIG_4", "BOOT_CONFIG_2", "", "", "", "", "EDP_BRIJ_EN", "", "", "BOOT_CONFIG_3", "WCI2_LTE_COEX_TXD", "WCI2_LTE_COEX_RXD", "", "", "", "", "FORCED_USB_BOOT_POL", "AP_TS_PEN_I2C_SDA", "AP_TS_PEN_I2C_SCL", "DP_HOT_PLUG_DET", "EC_IN_RW_ODL"; en_pp3300_touch: en-pp3300-touch-state { pins = "gpio87"; function = "gpio"; drive-strength = <2>; bias-disable; }; };