// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include "bcm2712.dtsi"

/ {
	compatible = "raspberrypi,5-model-b", "brcm,bcm2712";
	model = "Raspberry Pi 5";

	aliases {
		serial10 = &uart10;
	};

	chosen: chosen {
		stdout-path = "serial10:115200n8";
	};

	/* Will be filled by the bootloader */
	memory@0 {
		device_type = "memory";
		reg = <0 0 0 0x28000000>;
	};

	sd_io_1v8_reg: sd-io-1v8-reg {
		compatible = "regulator-gpio";
		regulator-name = "vdd-sd-io";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		regulator-always-on;
		regulator-settling-time-us = <5000>;
		gpios = <&gio_aon 3 GPIO_ACTIVE_HIGH>;
		states = <1800000 1>,
			 <3300000 0>;
	};

	sd_vcc_reg: sd-vcc-reg {
		compatible = "regulator-fixed";
		regulator-name = "vcc-sd";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		enable-active-high;
		gpios = <&gio_aon 4 GPIO_ACTIVE_HIGH>;
	};
};

/* The Debug UART, on Rpi5 it's on JST-SH 1.0mm 3-pin connector
 * labeled "UART", i.e. the interface with the system console.
 */
&uart10 {
	status = "okay";
};

/* SDIO1 is used to drive the SD card */
&sdio1 {
	vqmmc-supply = <&sd_io_1v8_reg>;
	vmmc-supply = <&sd_vcc_reg>;
	bus-width = <4>;
	sd-uhs-sdr50;
	sd-uhs-ddr50;
	sd-uhs-sdr104;
};

&soc {
	firmware: firmware {
		compatible = "raspberrypi,bcm2835-firmware", "simple-mfd";
		#address-cells = <1>;
		#size-cells = <1>;

		mboxes = <&mailbox>;
		dma-ranges;

		firmware_clocks: clocks {
			compatible = "raspberrypi,firmware-clocks";
			#clock-cells = <1>;
		};

		reset: reset {
			compatible = "raspberrypi,firmware-reset";
			#reset-cells = <1>;
		};
	};

	power: power {
		compatible = "raspberrypi,bcm2835-power";
		firmware = <&firmware>;
		#power-domain-cells = <1>;
	};
};

&hvs {
	clocks = <&firmware_clocks 4>, <&firmware_clocks 16>;
	clock-names = "core", "disp";
};

&hdmi0 {
	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
	clock-names = "hdmi", "bvb", "audio", "cec";
};

&hdmi1 {
	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
	clock-names = "hdmi", "bvb", "audio", "cec";
};