# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/clock/qcom,ipq9574-nsscc.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Qualcomm Networking Sub System Clock & Reset Controller on IPQ9574 and IPQ5424

maintainers:
  - Bjorn Andersson <andersson@kernel.org>
  - Anusha Rao <quic_anusha@quicinc.com>

description: |
  Qualcomm networking sub system clock control module provides the clocks,
  resets on IPQ9574 and IPQ5424

  See also:
    include/dt-bindings/clock/qcom,ipq5424-nsscc.h
    include/dt-bindings/clock/qcom,ipq9574-nsscc.h
    include/dt-bindings/reset/qcom,ipq5424-nsscc.h
    include/dt-bindings/reset/qcom,ipq9574-nsscc.h

properties:
  compatible:
    enum:
      - qcom,ipq5424-nsscc
      - qcom,ipq9574-nsscc

  clocks:
    items:
      - description: Board XO source
      - description: CMN_PLL NSS (Bias PLL cc) clock source. This clock rate
          can vary for different IPQ SoCs. For example, it is 1200 MHz on the
          IPQ9574 and 300 MHz on the IPQ5424.
      - description: CMN_PLL PPE (Bias PLL ubi nc) clock source. The clock
          rate can vary for different IPQ SoCs. For example, it is 353 MHz
          on the IPQ9574 and 375 MHz on the IPQ5424.
      - description: GCC GPLL0 OUT AUX clock source
      - description: Uniphy0 NSS Rx clock source
      - description: Uniphy0 NSS Tx clock source
      - description: Uniphy1 NSS Rx clock source
      - description: Uniphy1 NSS Tx clock source
      - description: Uniphy2 NSS Rx clock source
      - description: Uniphy2 NSS Tx clock source
      - description: GCC NSSCC clock source

  '#interconnect-cells':
    const: 1

  clock-names:
    items:
      - const: xo
      - enum:
          - nss_1200
          - nss
      - enum:
          - ppe_353
          - ppe
      - const: gpll0_out
      - const: uniphy0_rx
      - const: uniphy0_tx
      - const: uniphy1_rx
      - const: uniphy1_tx
      - const: uniphy2_rx
      - const: uniphy2_tx
      - const: bus

required:
  - compatible
  - clocks
  - clock-names

allOf:
  - $ref: qcom,gcc.yaml#
  - if:
      properties:
        compatible:
          const: qcom,ipq9574-nsscc
    then:
      properties:
        clock-names:
          items:
            - const: xo
            - const: nss_1200
            - const: ppe_353
            - const: gpll0_out
            - const: uniphy0_rx
            - const: uniphy0_tx
            - const: uniphy1_rx
            - const: uniphy1_tx
            - const: uniphy2_rx
            - const: uniphy2_tx
            - const: bus
    else:
      properties:
        clock-names:
          items:
            - const: xo
            - const: nss
            - const: ppe
            - const: gpll0_out
            - const: uniphy0_rx
            - const: uniphy0_tx
            - const: uniphy1_rx
            - const: uniphy1_tx
            - const: uniphy2_rx
            - const: uniphy2_tx
            - const: bus

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
    #include <dt-bindings/clock/qcom,ipq-cmn-pll.h>
    clock-controller@39b00000 {
      compatible = "qcom,ipq9574-nsscc";
      reg = <0x39b00000 0x80000>;
      clocks = <&xo_board_clk>,
               <&cmn_pll NSS_1200MHZ_CLK>,
               <&cmn_pll PPE_353MHZ_CLK>,
               <&gcc GPLL0_OUT_AUX>,
               <&uniphy 0>,
               <&uniphy 1>,
               <&uniphy 2>,
               <&uniphy 3>,
               <&uniphy 4>,
               <&uniphy 5>,
               <&gcc GCC_NSSCC_CLK>;
      clock-names = "xo",
                    "nss_1200",
                    "ppe_353",
                    "gpll0_out",
                    "uniphy0_rx",
                    "uniphy0_tx",
                    "uniphy1_rx",
                    "uniphy1_tx",
                    "uniphy2_rx",
                    "uniphy2_tx",
                    "bus";
      #clock-cells = <1>;
      #reset-cells = <1>;
      #interconnect-cells = <1>;
    };
...