/* SPDX-License-Identifier: GPL-2.0-only */ /* * linux/drivers/mmc/host/mmci.h - ARM PrimeCell MMCI PL180/1 driver * * Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved. */ #define MMCIPOWER 0x000 #define MCI_PWR_OFF 0x00 #define MCI_PWR_UP 0x02 #define MCI_PWR_ON 0x03 #define MCI_OD (1 << 6) #define MCI_ROD (1 << 7) /* * The ST Micro version does not have ROD and reuse the voltage registers for * direction settings. */ #define MCI_ST_DATA2DIREN (1 << 2) #define MCI_ST_CMDDIREN (1 << 3) #define MCI_ST_DATA0DIREN (1 << 4) #define MCI_ST_DATA31DIREN (1 << 5) #define MCI_ST_FBCLKEN (1 << 7) #define MCI_ST_DATA74DIREN (1 << 8) /* * The STM32 sdmmc does not have PWR_UP/OD/ROD * and uses the power register for */ #define MCI_STM32_PWR_CYC 0x02 #define MCI_STM32_VSWITCH BIT(2) #define MCI_STM32_VSWITCHEN BIT(3) #define MCI_STM32_DIRPOL BIT(4) #define MMCICLOCK 0x004 #define MCI_CLK_ENABLE (1 << 8) #define MCI_CLK_PWRSAVE (1 << 9) #define MCI_CLK_BYPASS (1 << 10) #define MCI_4BIT_BUS (1 << 11) /* * 8bit wide buses, hardware flow contronl, negative edges and clock inversion * supported in ST Micro U300 and Ux500 versions */ #define MCI_ST_8BIT_BUS (1 << 12) #define MCI_ST_U300_HWFCEN (1 << 13) #define MCI_ST_UX500_NEG_EDGE (1 << 13) #define MCI_ST_UX500_HWFCEN (1 << 14) #define MCI_ST_UX500_CLK_INV (1 << 15) /* Modified PL180 on Versatile Express platform */ #define MCI_ARM_HWFCEN (1 << 12) /* Modified on Qualcomm Integrations */ #define MCI_QCOM_CLK_WIDEBUS_8 (BIT(10) | BIT(11)) #define MCI_QCOM_CLK_FLOWENA BIT(12) #define MCI_QCOM_CLK_INVERTOUT BIT(13) /* select in latch data and command in */ #define MCI_QCOM_CLK_SELECT_IN_FBCLK BIT(15) #define MCI_QCOM_CLK_SELECT_IN_DDR_MODE (BIT(14) | BIT(15)) /* Modified on STM32 sdmmc */ #define MCI_STM32_CLK_CLKDIV_MSK GENMASK(9, 0) #define MCI_STM32_CLK_WIDEBUS_4 BIT(14) #define MCI_STM32_CLK_WIDEBUS_8 BIT(15) #define MCI_STM32_CLK_NEGEDGE BIT(16) #define MCI_STM32_CLK_HWFCEN BIT(17) #define MCI_STM32_CLK_DDR BIT(18) #define MCI_STM32_CLK_BUSSPEED BIT(19) #define MCI_STM32_CLK_SEL_MSK GENMASK(21, 20) #define MCI_STM32_CLK_SELCK (0 << 20) #define MCI_STM32_CLK_SELCKIN (1 << 20) #define MCI_STM32_CLK_SELFBCK (2 << 20) #define MMCIARGUMENT 0x008 /* The command register controls the Command Path State Machine (CPSM) */ #define MMCICOMMAND 0x00c #define MCI_CPSM_RESPONSE BIT(6) #define MCI_CPSM_LONGRSP BIT(7) #define MCI_CPSM_INTERRUPT BIT(8) #define MCI_CPSM_PENDING BIT(9) #define MCI_CPSM_ENABLE BIT(10) /* Command register flag extensions in the ST Micro versions */ #define MCI_CPSM_ST_SDIO_SUSP BIT(11) #define MCI_CPSM_ST_ENCMD_COMPL BIT(12) #define MCI_CPSM_ST_NIEN BIT(13) #define MCI_CPSM_ST_CE_ATACMD BIT(14) /* Command register flag extensions in the Qualcomm versions */ #define MCI_CPSM_QCOM_PROGENA BIT(11) #define MCI_CPSM_QCOM_DATCMD BIT(12) #define MCI_CPSM_QCOM_MCIABORT BIT(13) #define MCI_CPSM_QCOM_CCSENABLE BIT(14) #define MCI_CPSM_QCOM_CCSDISABLE BIT(15) #define MCI_CPSM_QCOM_AUTO_CMD19 BIT(16) #define MCI_CPSM_QCOM_AUTO_CMD21 BIT(21) /* Command register in STM32 sdmmc versions */ #define MCI_CPSM_STM32_CMDTRANS BIT(6) #define MCI_CPSM_STM32_CMDSTOP BIT(7) #define MCI_CPSM_STM32_WAITRESP_MASK GENMASK(9, 8) #define MCI_CPSM_STM32_NORSP (0 << 8) #define MCI_CPSM_STM32_SRSP_CRC (1 << 8) #define MCI_CPSM_STM32_SRSP (2 << 8) #define MCI_CPSM_STM32_LRSP_CRC (3 << 8) #define MCI_CPSM_STM32_ENABLE BIT(12) #define MMCIRESPCMD 0x010 #define MMCIRESPONSE0 0x014 #define MMCIRESPONSE1 0x018 #define MMCIRESPONSE2 0x01c #define MMCIRESPONSE3 0x020 #define MMCIDATATIMER 0x024 #define MMCIDATALENGTH 0x028 /* The data control register controls the Data Path State Machine (DPSM) */ #define MMCIDATACTRL 0x02c #define MCI_DPSM_ENABLE BIT(0) #define MCI_DPSM_DIRECTION BIT(1) #define MCI_DPSM_MODE BIT(2) #define MCI_DPSM_DMAENABLE BIT(3) #define MCI_DPSM_BLOCKSIZE BIT(4) /* Control register extensions in the ST Micro U300 and Ux500 versions */ #define MCI_DPSM_ST_RWSTART BIT(8) #define MCI_DPSM_ST_RWSTOP BIT(9) #define MCI_DPSM_ST_RWMOD BIT(10) #define MCI_DPSM_ST_SDIOEN BIT(11) /* Control register extensions in the ST Micro Ux500 versions */ #define MCI_DPSM_ST_DMAREQCTL BIT(12) #define MCI_DPSM_ST_DBOOTMODEEN BIT(13) #define MCI_DPSM_ST_BUSYMODE BIT(14) #define MCI_DPSM_ST_DDRMODE BIT(15) /* Control register extensions in the Qualcomm versions */ #define MCI_DPSM_QCOM_DATA_PEND BIT(17) #define MCI_DPSM_QCOM_RX_DATA_PEND BIT(20) /* Control register extensions in STM32 versions */ #define MCI_DPSM_STM32_MODE_BLOCK (0 << 2) #define MCI_DPSM_STM32_MODE_SDIO (1 << 2) #define MCI_DPSM_STM32_MODE_STREAM (2 << 2) #define MCI_DPSM_STM32_MODE_BLOCK_STOP (3 << 2) #define MMCIDATACNT 0x030 #define MMCISTATUS 0x034 #define MCI_CMDCRCFAIL (1 << 0) #define MCI_DATACRCFAIL (1 << 1) #define MCI_CMDTIMEOUT (1 << 2) #define MCI_DATATIMEOUT (1 << 3) #define MCI_TXUNDERRUN (1 << 4) #define MCI_RXOVERRUN (1 << 5) #define MCI_CMDRESPEND (1 << 6) #define MCI_CMDSENT (1 << 7) #define MCI_DATAEND (1 << 8) #define MCI_STARTBITERR (1 << 9) #define MCI_DATABLOCKEND (1 << 10) #define MCI_CMDACTIVE (1 << 11) #define MCI_TXACTIVE (1 << 12) #define MCI_RXACTIVE (1 << 13) #define MCI_TXFIFOHALFEMPTY (1 << 14) #define MCI_RXFIFOHALFFULL (1 << 15) #define MCI_TXFIFOFULL (1 << 16) #define MCI_RXFIFOFULL (1 << 17) #define MCI_TXFIFOEMPTY (1 << 18) #define MCI_RXFIFOEMPTY (1 << 19) #define MCI_TXDATAAVLBL (1 << 20) #define MCI_RXDATAAVLBL (1 << 21) /* Extended status bits for the ST Micro variants */ #define MCI_ST_SDIOIT (1 << 22) #define MCI_ST_CEATAEND (1 << 23) #define MCI_ST_CARDBUSY (1 << 24) /* Extended status bits for the STM32 variants */ #define MCI_STM32_BUSYD0 BIT(20) #define MCI_STM32_BUSYD0END BIT(21) #define MCI_STM32_VSWEND BIT(25) #define MMCICLEAR 0x038 #define MCI_CMDCRCFAILCLR (1 << 0) #define MCI_DATACRCFAILCLR (1 << 1) #define MCI_CMDTIMEOUTCLR (1 << 2) #define MCI_DATATIMEOUTCLR (1 << 3) #define MCI_TXUNDERRUNCLR (1 << 4) #define MCI_RXOVERRUNCLR (1 << 5) #define MCI_CMDRESPENDCLR (1 << 6) #define MCI_CMDSENTCLR (1 << 7) #define MCI_DATAENDCLR (1 << 8) #define MCI_STARTBITERRCLR (1 << 9) #define MCI_DATABLOCKENDCLR (1 << 10) /* Extended status bits for the ST Micro variants */ #define MCI_ST_SDIOITC (1 << 22) #define MCI_ST_CEATAENDC (1 << 23) #define MCI_ST_BUSYENDC (1 << 24) /* Extended clear bits for the STM32 variants */ #define MCI_STM32_VSWENDC BIT(25) #define MCI_STM32_CKSTOPC BIT(26) #define MMCIMASK0 0x03c #define MCI_CMDCRCFAILMASK (1 << 0) #define MCI_DATACRCFAILMASK (1 << 1) #define MCI_CMDTIMEOUTMASK (1 << 2) #define MCI_DATATIMEOUTMASK (1 << 3) #define MCI_TXUNDERRUNMASK (1 << 4) #define MCI_RXOVERRUNMASK (1 << 5) #define MCI_CMDRESPENDMASK (1 << 6) #define MCI_CMDSENTMASK (1 << 7) #define MCI_DATAENDMASK (1 << 8) #define MCI_STARTBITERRMASK (1 << 9) #define MCI_DATABLOCKENDMASK (1 << 10) #define MCI_CMDACTIVEMASK (1 << 11) #define MCI_TXACTIVEMASK (1 << 12) #define MCI_RXACTIVEMASK (1 << 13) #define MCI_TXFIFOHALFEMPTYMASK (1 << 14) #define MCI_RXFIFOHALFFULLMASK (1 << 15) #define MCI_TXFIFOFULLMASK (1 << 16) #define MCI_RXFIFOFULLMASK (1 << 17) #define MCI_TXFIFOEMPTYMASK (1 << 18) #define MCI_RXFIFOEMPTYMASK (1 << 19) #define MCI_TXDATAAVLBLMASK (1 << 20) #define MCI_RXDATAAVLBLMASK (1 << 21) /* Extended status bits for the ST Micro variants */ #define MCI_ST_SDIOITMASK (1 << 22) #define MCI_ST_CEATAENDMASK (1 << 23) #define MCI_ST_BUSYENDMASK (1 << 24) /* Extended status bits for the STM32 variants */ #define MCI_STM32_BUSYD0ENDMASK BIT(21) #define MMCIMASK1 0x040 /* STM32 sdmmc data FIFO threshold register */ #define MMCI_STM32_FIFOTHRR 0x044 #define MMCI_STM32_THR_MASK GENMASK(3, 0) #define MMCIFIFOCNT 0x048 #define MMCIFIFO 0x080 /* to 0x0bc */ /* STM32 sdmmc registers for IDMA (Internal DMA) */ #define MMCI_STM32_IDMACTRLR 0x050 #define MMCI_STM32_IDMAEN BIT(0) #define MMCI_STM32_IDMALLIEN BIT(1) #define MMCI_STM32_IDMABSIZER 0x054 #define MMCI_STM32_IDMABASE0R 0x058 #define MMCI_STM32_IDMALAR 0x64 #define MMCI_STM32_IDMALA_MASK GENMASK(13, 0) #define MMCI_STM32_ABR BIT(29) #define MMCI_STM32_ULS BIT(30) #define MMCI_STM32_ULA BIT(31) #define MMCI_STM32_IDMABAR 0x68 #define MCI_IRQENABLE \ (MCI_CMDCRCFAILMASK | MCI_DATACRCFAILMASK | MCI_CMDTIMEOUTMASK | \ MCI_DATATIMEOUTMASK | MCI_TXUNDERRUNMASK | MCI_RXOVERRUNMASK | \ MCI_CMDRESPENDMASK | MCI_CMDSENTMASK) /* These interrupts are directed to IRQ1 when two IRQ lines are available */ #define MCI_IRQ_PIO_MASK \ (MCI_RXFIFOHALFFULLMASK | MCI_RXDATAAVLBLMASK | \ MCI_TXFIFOHALFEMPTYMASK) #define MCI_IRQ_PIO_STM32_MASK \ (MCI_RXFIFOHALFFULLMASK | MCI_TXFIFOHALFEMPTYMASK) #define NR_SG 128 #define MMCI_PINCTRL_STATE_OPENDRAIN "opendrain" struct clk; struct dma_chan; struct mmci_host; /** * enum mmci_busy_state - enumerate the busy detect wait states * * This is used for the state machine waiting for different busy detect * interrupts on hardware that fire a single IRQ for start and end of * the busy detect phase on DAT0. */ enum mmci_busy_state { MMCI_BUSY_WAITING_FOR_START_IRQ, MMCI_BUSY_WAITING_FOR_END_IRQ, MMCI_BUSY_DONE, }; /** * struct variant_data - MMCI variant-specific quirks * @clkreg: default value for MCICLOCK register * @clkreg_enable: enable value for MMCICLOCK register * @clkreg_8bit_bus_enable: enable value for 8 bit bus * @clkreg_neg_edge_enable: enable value for inverted data/cmd output * @cmdreg_cpsm_enable: enable value for CPSM * @cmdreg_lrsp_crc: enable value for long response with crc * @cmdreg_srsp_crc: enable value for short response with crc * @cmdreg_srsp: enable value for short response without crc * @cmdreg_stop: enable value for stop and abort transmission * @datalength_bits: number of bits in the MMCIDATALENGTH register * @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY * is asserted (likewise for RX) * @fifohalfsize: number of bytes that can be written when MCI_TXFIFOHALFEMPTY * is asserted (likewise for RX) * @data_cmd_enable: enable value for data commands. * @st_sdio: enable ST specific SDIO logic * @st_clkdiv: true if using a ST-specific clock divider algorithm * @stm32_clkdiv: true if using a STM32-specific clock divider algorithm * @datactrl_mask_ddrmode: ddr mode mask in datactrl register. * @datactrl_mask_sdio: SDIO enable mask in datactrl register * @datactrl_blocksz: block size in power of two * @datactrl_any_blocksz: true if block any block sizes are accepted by * hardware, such as with some SDIO traffic that send * odd packets. * @dma_power_of_2: DMA only works with blocks that are a power of 2. * @datactrl_first: true if data must be setup before send command * @datacnt_useless: true if you could not use datacnt register to read * remaining data * @pwrreg_powerup: power up value for MMCIPOWER register * @f_max: maximum clk frequency supported by the controller. * @signal_direction: input/out direction of bus signals can be indicated * @pwrreg_clkgate: MMCIPOWER register must be used to gate the clock * @busy_detect: true if the variant supports busy detection on DAT0. * @busy_timeout: true if the variant starts data timer when the DPSM * enter in Wait_R or Busy state. * @busy_dpsm_flag: bitmask enabling busy detection in the DPSM * @busy_detect_flag: bitmask identifying the bit in the MMCISTATUS register * indicating that the card is busy * @busy_detect_mask: bitmask identifying the bit in the MMCIMASK0 to mask for * getting busy end detection interrupts * @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply * @explicit_mclk_control: enable explicit mclk control in driver. * @qcom_fifo: enables qcom specific fifo pio read logic. * @qcom_dml: enables qcom specific dma glue for dma transfers. * @reversed_irq_handling: handle data irq before cmd irq. * @mmcimask1: true if variant have a MMCIMASK1 register. * @irq_pio_mask: bitmask used to manage interrupt pio transfert in mmcimask * register * @start_err: bitmask identifying the STARTBITERR bit inside MMCISTATUS * register. * @opendrain: bitmask identifying the OPENDRAIN bit inside MMCIPOWER register * @dma_lli: true if variant has dma link list feature. * @supports_sdio_irq: allow SD I/O card to interrupt the host * @stm32_idmabsize_mask: stm32 sdmmc idma buffer size. * @dma_flow_controller: use peripheral as flow controller for DMA. */ struct variant_data { unsigned int clkreg; unsigned int clkreg_enable; unsigned int clkreg_8bit_bus_enable; unsigned int clkreg_neg_edge_enable; unsigned int cmdreg_cpsm_enable; unsigned int cmdreg_lrsp_crc; unsigned int cmdreg_srsp_crc; unsigned int cmdreg_srsp; unsigned int cmdreg_stop; unsigned int datalength_bits; unsigned int fifosize; unsigned int fifohalfsize; unsigned int data_cmd_enable; unsigned int datactrl_mask_ddrmode; unsigned int datactrl_mask_sdio; unsigned int datactrl_blocksz; u8 datactrl_any_blocksz:1; u8 dma_power_of_2:1; u8 datactrl_first:1; u8 datacnt_useless:1; u8 st_sdio:1; u8 st_clkdiv:1; u8 stm32_clkdiv:1; u32 pwrreg_powerup; u32 f_max; u8 signal_direction:1; u8 pwrreg_clkgate:1; u8 busy_detect:1; u8 busy_timeout:1; u32 busy_dpsm_flag; u32 busy_detect_flag; u32 busy_detect_mask; u8 pwrreg_nopower:1; u8 explicit_mclk_control:1; u8 qcom_fifo:1; u8 qcom_dml:1; u8 reversed_irq_handling:1; u8 mmcimask1:1; unsigned int irq_pio_mask; u32 start_err; u32 opendrain; u8 dma_lli:1; bool supports_sdio_irq; u32 stm32_idmabsize_mask; u32 stm32_idmabsize_align; bool dma_flow_controller; void (*init)(struct mmci_host *host); }; /* mmci variant callbacks */ struct mmci_host_ops { int (*validate_data)(struct mmci_host *host, struct mmc_data *data); int (*prep_data)(struct mmci_host *host, struct mmc_data *data, bool next); void (*unprep_data)(struct mmci_host *host, struct mmc_data *data, int err); u32 (*get_datactrl_cfg)(struct mmci_host *host); void (*get_next_data)(struct mmci_host *host, struct mmc_data *data); int (*dma_setup)(struct mmci_host *host); void (*dma_release)(struct mmci_host *host); int (*dma_start)(struct mmci_host *host, unsigned int *datactrl); void (*dma_finalize)(struct mmci_host *host, struct mmc_data *data); void (*dma_error)(struct mmci_host *host); void (*set_clkreg)(struct mmci_host *host, unsigned int desired); void (*set_pwrreg)(struct mmci_host *host, unsigned int pwr); bool (*busy_complete)(struct mmci_host *host, struct mmc_command *cmd, u32 status, u32 err_msk); void (*pre_sig_volt_switch)(struct mmci_host *host); int (*post_sig_volt_switch)(struct mmci_host *host, struct mmc_ios *ios); }; struct mmci_host { phys_addr_t phybase; void __iomem *base; struct mmc_request *mrq; struct mmc_command *cmd; struct mmc_command stop_abort; struct mmc_data *data; struct mmc_host *mmc; struct clk *clk; u8 singleirq:1; struct reset_control *rst; spinlock_t lock; unsigned int mclk; /* cached value of requested clk in set_ios */ unsigned int clock_cache; unsigned int cclk; u32 pwr_reg; u32 pwr_reg_add; u32 clk_reg; u32 clk_reg_add; u32 datactrl_reg; enum mmci_busy_state busy_state; u32 busy_status; u32 mask1_reg; u8 vqmmc_enabled:1; struct mmci_platform_data *plat; struct mmc_host_ops *mmc_ops; struct mmci_host_ops *ops; struct variant_data *variant; void *variant_priv; struct pinctrl *pinctrl; struct pinctrl_state *pins_opendrain; u8 hw_designer; u8 hw_revision:4; struct timer_list timer; unsigned int oldstat; u32 irq_action; /* pio stuff */ struct sg_mapping_iter sg_miter; unsigned int size; int (*get_rx_fifocnt)(struct mmci_host *h, u32 status, int remain); u8 use_dma:1; u8 dma_in_progress:1; void *dma_priv; s32 next_cookie; struct delayed_work ux500_busy_timeout_work; }; #define dma_inprogress(host) ((host)->dma_in_progress) void mmci_write_clkreg(struct mmci_host *host, u32 clk); void mmci_write_pwrreg(struct mmci_host *host, u32 pwr); static inline u32 mmci_dctrl_blksz(struct mmci_host *host) { return (ffs(host->data->blksz) - 1) << 4; } #ifdef CONFIG_DMA_ENGINE int mmci_dmae_prep_data(struct mmci_host *host, struct mmc_data *data, bool next); void mmci_dmae_unprep_data(struct mmci_host *host, struct mmc_data *data, int err); void mmci_dmae_get_next_data(struct mmci_host *host, struct mmc_data *data); int mmci_dmae_setup(struct mmci_host *host); void mmci_dmae_release(struct mmci_host *host); int mmci_dmae_start(struct mmci_host *host, unsigned int *datactrl); void mmci_dmae_finalize(struct mmci_host *host, struct mmc_data *data); void mmci_dmae_error(struct mmci_host *host); #endif #ifdef CONFIG_MMC_QCOM_DML void qcom_variant_init(struct mmci_host *host); #else static inline void qcom_variant_init(struct mmci_host *host) {} #endif #ifdef CONFIG_MMC_STM32_SDMMC void sdmmc_variant_init(struct mmci_host *host); #else static inline void sdmmc_variant_init(struct mmci_host *host) {} #endif