// SPDX-License-Identifier: GPL-2.0-only /* * Awinic AW9523B i2c pin controller driver * Copyright (c) 2020, AngeloGioacchino Del Regno */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define AW9523_MAX_FUNCS 2 #define AW9523_NUM_PORTS 2 #define AW9523_PINS_PER_PORT 8 /* * HW needs at least 20uS for reset and at least 1-2uS to recover from * reset, but we have to account for eventual board quirks, if any: * for this reason, keep reset asserted for 50uS and wait for 20uS * to recover from the reset. */ #define AW9523_HW_RESET_US 50 #define AW9523_HW_RESET_RECOVERY_US 20 /* Port 0: P0_0...P0_7 - Port 1: P1_0...P1_7 */ #define AW9523_PIN_TO_PORT(pin) (pin >> 3) #define AW9523_REG_IN_STATE(pin) (0x00 + AW9523_PIN_TO_PORT(pin)) #define AW9523_REG_OUT_STATE(pin) (0x02 + AW9523_PIN_TO_PORT(pin)) #define AW9523_REG_CONF_STATE(pin) (0x04 + AW9523_PIN_TO_PORT(pin)) #define AW9523_REG_INTR_DIS(pin) (0x06 + AW9523_PIN_TO_PORT(pin)) #define AW9523_REG_CHIPID 0x10 #define AW9523_VAL_EXPECTED_CHIPID 0x23 #define AW9523_REG_GCR 0x11 #define AW9523_GCR_ISEL_MASK GENMASK(0, 1) #define AW9523_GCR_GPOMD_MASK BIT(4) #define AW9523_REG_PORT_MODE(pin) (0x12 + AW9523_PIN_TO_PORT(pin)) #define AW9523_REG_SOFT_RESET 0x7f #define AW9523_VAL_RESET 0x00 /* * struct aw9523_irq - Interrupt controller structure * @lock: mutex locking for the irq bus * @cached_gpio: stores the previous gpio status for bit comparison */ struct aw9523_irq { struct mutex lock; u16 cached_gpio; }; /* * struct aw9523 - Main driver structure * @dev: device handle * @regmap: regmap handle for current device * @i2c_lock: Mutex lock for i2c operations * @reset_gpio: Hardware reset (RSTN) signal GPIO * @vio_vreg: VCC regulator (Optional) * @pctl: pinctrl handle for current device * @gpio: structure holding gpiochip params * @irq: Interrupt controller structure */ struct aw9523 { struct device *dev; struct regmap *regmap; struct mutex i2c_lock; struct gpio_desc *reset_gpio; int vio_vreg; struct pinctrl_dev *pctl; struct gpio_chip gpio; struct aw9523_irq *irq; }; static const struct pinctrl_pin_desc aw9523_pins[] = { /* Port 0 */ PINCTRL_PIN(0, "gpio0"), PINCTRL_PIN(1, "gpio1"), PINCTRL_PIN(2, "gpio2"), PINCTRL_PIN(3, "gpio3"), PINCTRL_PIN(4, "gpio4"), PINCTRL_PIN(5, "gpio5"), PINCTRL_PIN(6, "gpio6"), PINCTRL_PIN(7, "gpio7"), /* Port 1 */ PINCTRL_PIN(8, "gpio8"), PINCTRL_PIN(9, "gpio9"), PINCTRL_PIN(10, "gpio10"), PINCTRL_PIN(11, "gpio11"), PINCTRL_PIN(12, "gpio12"), PINCTRL_PIN(13, "gpio13"), PINCTRL_PIN(14, "gpio14"), PINCTRL_PIN(15, "gpio15"), }; static int aw9523_pinctrl_get_groups_count(struct pinctrl_dev *pctldev) { return ARRAY_SIZE(aw9523_pins); } static const char *aw9523_pinctrl_get_group_name(struct pinctrl_dev *pctldev, unsigned int selector) { return aw9523_pins[selector].name; } static int aw9523_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, unsigned int selector, const unsigned int **pins, unsigned int *num_pins) { *pins = &aw9523_pins[selector].number; *num_pins = 1; return 0; } static const struct pinctrl_ops aw9523_pinctrl_ops = { .get_groups_count = aw9523_pinctrl_get_groups_count, .get_group_pins = aw9523_pinctrl_get_group_pins, .get_group_name = aw9523_pinctrl_get_group_name, .dt_node_to_map = pinconf_generic_dt_node_to_map_pin, .dt_free_map = pinconf_generic_dt_free_map, }; static const char * const gpio_pwm_groups[] = { "gpio0", "gpio1", "gpio2", "gpio3", /* 0-3 */ "gpio4", "gpio5", "gpio6", "gpio7", /* 4-7 */ "gpio8", "gpio9", "gpio10", "gpio11", /* 8-11 */ "gpio12", "gpio13", "gpio14", "gpio15", /* 11-15 */ }; /* Warning: Do NOT reorder this array */ static const struct pinfunction aw9523_pmx[] = { PINCTRL_PINFUNCTION("pwm", gpio_pwm_groups, ARRAY_SIZE(gpio_pwm_groups)), PINCTRL_PINFUNCTION("gpio", gpio_pwm_groups, ARRAY_SIZE(gpio_pwm_groups)), }; static int aw9523_pmx_get_funcs_count(struct pinctrl_dev *pctl) { return ARRAY_SIZE(aw9523_pmx); } static const char *aw9523_pmx_get_fname(struct pinctrl_dev *pctl, unsigned int sel) { return aw9523_pmx[sel].name; } static int aw9523_pmx_get_groups(struct pinctrl_dev *pctl, unsigned int sel, const char * const **groups, unsigned int * const ngroups) { *groups = aw9523_pmx[sel].groups; *ngroups = aw9523_pmx[sel].ngroups; return 0; } static int aw9523_pmx_set_mux(struct pinctrl_dev *pctl, unsigned int fsel, unsigned int grp) { struct aw9523 *awi = pinctrl_dev_get_drvdata(pctl); int ret, pin = aw9523_pins[grp].number % AW9523_PINS_PER_PORT; if (fsel >= ARRAY_SIZE(aw9523_pmx)) return -EINVAL; /* * This maps directly to the aw9523_pmx array: programming a * high bit means "gpio" and a low bit means "pwm". */ mutex_lock(&awi->i2c_lock); ret = regmap_update_bits(awi->regmap, AW9523_REG_PORT_MODE(pin), BIT(pin), (fsel ? BIT(pin) : 0)); mutex_unlock(&awi->i2c_lock); return ret; } static const struct pinmux_ops aw9523_pinmux_ops = { .get_functions_count = aw9523_pmx_get_funcs_count, .get_function_name = aw9523_pmx_get_fname, .get_function_groups = aw9523_pmx_get_groups, .set_mux = aw9523_pmx_set_mux, }; static int aw9523_pcfg_param_to_reg(enum pin_config_param pcp, int pin, u8 *r) { u8 reg; switch (pcp) { case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: case PIN_CONFIG_BIAS_PULL_DOWN: case PIN_CONFIG_BIAS_PULL_UP: reg = AW9523_REG_IN_STATE(pin); break; case PIN_CONFIG_DRIVE_OPEN_DRAIN: case PIN_CONFIG_DRIVE_PUSH_PULL: reg = AW9523_REG_GCR; break; case PIN_CONFIG_INPUT_ENABLE: case PIN_CONFIG_OUTPUT_ENABLE: reg = AW9523_REG_CONF_STATE(pin); break; case PIN_CONFIG_OUTPUT: reg = AW9523_REG_OUT_STATE(pin); break; default: return -ENOTSUPP; } *r = reg; return 0; } static int aw9523_pconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config) { struct aw9523 *awi = pinctrl_dev_get_drvdata(pctldev); enum pin_config_param param = pinconf_to_config_param(*config); int regbit = pin % AW9523_PINS_PER_PORT; unsigned int val; u8 reg; int rc; rc = aw9523_pcfg_param_to_reg(param, pin, ®); if (rc) return rc; mutex_lock(&awi->i2c_lock); rc = regmap_read(awi->regmap, reg, &val); mutex_unlock(&awi->i2c_lock); if (rc) return rc; switch (param) { case PIN_CONFIG_BIAS_PULL_UP: case PIN_CONFIG_INPUT_ENABLE: case PIN_CONFIG_OUTPUT: val &= BIT(regbit); break; case PIN_CONFIG_BIAS_PULL_DOWN: case PIN_CONFIG_OUTPUT_ENABLE: val &= BIT(regbit); val = !val; break; case PIN_CONFIG_DRIVE_OPEN_DRAIN: if (pin >= AW9523_PINS_PER_PORT) val = 0; else val = !FIELD_GET(AW9523_GCR_GPOMD_MASK, val); break; case PIN_CONFIG_DRIVE_PUSH_PULL: if (pin >= AW9523_PINS_PER_PORT) val = 1; else val = FIELD_GET(AW9523_GCR_GPOMD_MASK, val); break; default: return -ENOTSUPP; } if (val < 1) return -EINVAL; *config = pinconf_to_config_packed(param, !!val); return rc; } static int aw9523_pconf_set(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *configs, unsigned int num_configs) { struct aw9523 *awi = pinctrl_dev_get_drvdata(pctldev); enum pin_config_param param; int regbit = pin % AW9523_PINS_PER_PORT; u32 arg; u8 reg; unsigned int mask, val; int i, rc; mutex_lock(&awi->i2c_lock); for (i = 0; i < num_configs; i++) { param = pinconf_to_config_param(configs[i]); arg = pinconf_to_config_argument(configs[i]); rc = aw9523_pcfg_param_to_reg(param, pin, ®); if (rc) goto end; switch (param) { case PIN_CONFIG_OUTPUT: /* First, enable pin output */ rc = regmap_update_bits(awi->regmap, AW9523_REG_CONF_STATE(pin), BIT(regbit), 0); if (rc) goto end; /* Then, fall through to config output level */ fallthrough; case PIN_CONFIG_OUTPUT_ENABLE: arg = !arg; fallthrough; case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: case PIN_CONFIG_BIAS_PULL_DOWN: case PIN_CONFIG_BIAS_PULL_UP: case PIN_CONFIG_INPUT_ENABLE: mask = BIT(regbit); val = arg ? BIT(regbit) : 0; break; case PIN_CONFIG_DRIVE_OPEN_DRAIN: /* Open-Drain is supported only on port 0 */ if (pin >= AW9523_PINS_PER_PORT) { rc = -ENOTSUPP; goto end; } mask = AW9523_GCR_GPOMD_MASK; val = 0; break; case PIN_CONFIG_DRIVE_PUSH_PULL: /* Port 1 is always Push-Pull */ if (pin >= AW9523_PINS_PER_PORT) { mask = 0; val = 0; continue; } mask = AW9523_GCR_GPOMD_MASK; val = AW9523_GCR_GPOMD_MASK; break; default: rc = -ENOTSUPP; goto end; } rc = regmap_update_bits(awi->regmap, reg, mask, val); if (rc) goto end; } end: mutex_unlock(&awi->i2c_lock); return rc; } static const struct pinconf_ops aw9523_pinconf_ops = { .pin_config_get = aw9523_pconf_get, .pin_config_set = aw9523_pconf_set, .is_generic = true, }; /* * aw9523_get_pin_direction - Get pin direction * @regmap: Regmap structure * @pin: gpiolib pin number * @n: pin index in port register * * Return: Pin direction for success or negative number for error */ static int aw9523_get_pin_direction(struct regmap *regmap, u8 pin, u8 n) { int ret; ret = regmap_test_bits(regmap, AW9523_REG_CONF_STATE(pin), BIT(n)); if (ret < 0) return ret; return ret ? GPIO_LINE_DIRECTION_IN : GPIO_LINE_DIRECTION_OUT; } /* * aw9523_get_port_state - Get input or output state for entire port * @regmap: Regmap structure * @pin: gpiolib pin number * @regbit: hw pin index, used to retrieve port number * @state: returned port state * * Return: Zero for success or negative number for error */ static int aw9523_get_port_state(struct regmap *regmap, u8 pin, u8 regbit, unsigned int *state) { u8 reg; int dir; dir = aw9523_get_pin_direction(regmap, pin, regbit); if (dir < 0) return dir; if (dir == GPIO_LINE_DIRECTION_IN) reg = AW9523_REG_IN_STATE(pin); else reg = AW9523_REG_OUT_STATE(pin); return regmap_read(regmap, reg, state); } static int aw9523_gpio_irq_type(struct irq_data *d, unsigned int type) { switch (type) { case IRQ_TYPE_NONE: case IRQ_TYPE_EDGE_BOTH: return 0; default: return -EINVAL; }; } /* * aw9523_irq_mask - Mask interrupt * @d: irq data * * Sets which interrupt to mask in the bitmap; * The interrupt will be masked when unlocking the irq bus. */ static void aw9523_irq_mask(struct irq_data *d) { struct aw9523 *awi = gpiochip_get_data(irq_data_get_irq_chip_data(d)); irq_hw_number_t hwirq = irqd_to_hwirq(d); unsigned int n = hwirq % AW9523_PINS_PER_PORT; regmap_update_bits(awi->regmap, AW9523_REG_INTR_DIS(hwirq), BIT(n), BIT(n)); gpiochip_disable_irq(&awi->gpio, hwirq); } /* * aw9523_irq_unmask - Unmask interrupt * @d: irq data * * Sets which interrupt to unmask in the bitmap; * The interrupt will be masked when unlocking the irq bus. */ static void aw9523_irq_unmask(struct irq_data *d) { struct aw9523 *awi = gpiochip_get_data(irq_data_get_irq_chip_data(d)); irq_hw_number_t hwirq = irqd_to_hwirq(d); unsigned int n = hwirq % AW9523_PINS_PER_PORT; gpiochip_enable_irq(&awi->gpio, hwirq); regmap_update_bits(awi->regmap, AW9523_REG_INTR_DIS(hwirq), BIT(n), 0); } static irqreturn_t aw9523_irq_thread_func(int irq, void *dev_id) { struct aw9523 *awi = (struct aw9523 *)dev_id; unsigned long n, val = 0; unsigned long changed_gpio; unsigned int tmp, port_pin, i, ret; for (i = 0; i < AW9523_NUM_PORTS; i++) { port_pin = i * AW9523_PINS_PER_PORT; ret = regmap_read(awi->regmap, AW9523_REG_IN_STATE(port_pin), &tmp); if (ret) return ret; val |= (u8)tmp << (i * 8); } /* Handle GPIO input release interrupt as well */ changed_gpio = awi->irq->cached_gpio ^ val; awi->irq->cached_gpio = val; /* * To avoid up to four *slow* i2c reads from any driver hooked * up to our interrupts, just check for the irq_find_mapping * result: if the interrupt is not mapped, then we don't want * to care about it. */ for_each_set_bit(n, &changed_gpio, awi->gpio.ngpio) { tmp = irq_find_mapping(awi->gpio.irq.domain, n); if (tmp <= 0) continue; handle_nested_irq(tmp); } return IRQ_HANDLED; } /* * aw9523_irq_bus_lock - Grab lock for interrupt operation * @d: irq data */ static void aw9523_irq_bus_lock(struct irq_data *d) { struct aw9523 *awi = gpiochip_get_data(irq_data_get_irq_chip_data(d)); mutex_lock(&awi->irq->lock); regcache_cache_only(awi->regmap, true); } /* * aw9523_irq_bus_sync_unlock - Synchronize state and unlock * @d: irq data * * Writes the interrupt mask bits (found in the bit map) to the * hardware, then unlocks the bus. */ static void aw9523_irq_bus_sync_unlock(struct irq_data *d) { struct aw9523 *awi = gpiochip_get_data(irq_data_get_irq_chip_data(d)); regcache_cache_only(awi->regmap, false); regcache_sync(awi->regmap); mutex_unlock(&awi->irq->lock); } static int aw9523_gpio_get_direction(struct gpio_chip *chip, unsigned int offset) { struct aw9523 *awi = gpiochip_get_data(chip); u8 regbit = offset % AW9523_PINS_PER_PORT; int ret; mutex_lock(&awi->i2c_lock); ret = aw9523_get_pin_direction(awi->regmap, offset, regbit); mutex_unlock(&awi->i2c_lock); return ret; } static int aw9523_gpio_get(struct gpio_chip *chip, unsigned int offset) { struct aw9523 *awi = gpiochip_get_data(chip); u8 regbit = offset % AW9523_PINS_PER_PORT; unsigned int val; int ret; mutex_lock(&awi->i2c_lock); ret = aw9523_get_port_state(awi->regmap, offset, regbit, &val); mutex_unlock(&awi->i2c_lock); if (ret) return ret; return !!(val & BIT(regbit)); } /** * _aw9523_gpio_get_multiple - Get I/O state for an entire port * @awi: Controller data * @regbit: hw pin index, used to retrieve port number * @state: returned port I/O state * @mask: lines to read values for * * Return: Zero for success or negative number for error */ static int _aw9523_gpio_get_multiple(struct aw9523 *awi, u8 regbit, u8 *state, u8 mask) { u32 dir_in, val; u8 m; int ret; /* Registers are 8-bits wide */ ret = regmap_read(awi->regmap, AW9523_REG_CONF_STATE(regbit), &dir_in); if (ret) return ret; *state = 0; m = mask & dir_in; if (m) { ret = regmap_read(awi->regmap, AW9523_REG_IN_STATE(regbit), &val); if (ret) return ret; *state |= (u8)val & m; } m = mask & ~dir_in; if (m) { ret = regmap_read(awi->regmap, AW9523_REG_OUT_STATE(regbit), &val); if (ret) return ret; *state |= (u8)val & m; } return 0; } static int aw9523_gpio_get_multiple(struct gpio_chip *chip, unsigned long *mask, unsigned long *bits) { struct aw9523 *awi = gpiochip_get_data(chip); u8 m, state = 0; int ret; mutex_lock(&awi->i2c_lock); /* Port 0 (gpio 0-7) */ m = *mask; if (m) { ret = _aw9523_gpio_get_multiple(awi, 0, &state, m); if (ret) goto out; } *bits = state; /* Port 1 (gpio 8-15) */ m = *mask >> 8; if (m) { ret = _aw9523_gpio_get_multiple(awi, AW9523_PINS_PER_PORT, &state, m); if (ret) goto out; *bits |= (state << 8); } out: mutex_unlock(&awi->i2c_lock); return ret; } static void aw9523_gpio_set_multiple(struct gpio_chip *chip, unsigned long *mask, unsigned long *bits) { struct aw9523 *awi = gpiochip_get_data(chip); u8 mask_lo, mask_hi, bits_lo, bits_hi; unsigned int reg; int ret; mask_lo = *mask; mask_hi = *mask >> 8; bits_lo = *bits; bits_hi = *bits >> 8; mutex_lock(&awi->i2c_lock); if (mask_hi) { reg = AW9523_REG_OUT_STATE(AW9523_PINS_PER_PORT); ret = regmap_write_bits(awi->regmap, reg, mask_hi, bits_hi); if (ret) dev_warn(awi->dev, "Cannot write port1 out level\n"); } if (mask_lo) { reg = AW9523_REG_OUT_STATE(0); ret = regmap_write_bits(awi->regmap, reg, mask_lo, bits_lo); if (ret) dev_warn(awi->dev, "Cannot write port0 out level\n"); } mutex_unlock(&awi->i2c_lock); } static void aw9523_gpio_set(struct gpio_chip *chip, unsigned int offset, int value) { struct aw9523 *awi = gpiochip_get_data(chip); u8 regbit = offset % AW9523_PINS_PER_PORT; mutex_lock(&awi->i2c_lock); regmap_update_bits(awi->regmap, AW9523_REG_OUT_STATE(offset), BIT(regbit), value ? BIT(regbit) : 0); mutex_unlock(&awi->i2c_lock); } static int aw9523_direction_input(struct gpio_chip *chip, unsigned int offset) { struct aw9523 *awi = gpiochip_get_data(chip); u8 regbit = offset % AW9523_PINS_PER_PORT; int ret; mutex_lock(&awi->i2c_lock); ret = regmap_update_bits(awi->regmap, AW9523_REG_CONF_STATE(offset), BIT(regbit), BIT(regbit)); mutex_unlock(&awi->i2c_lock); return ret; } static int aw9523_direction_output(struct gpio_chip *chip, unsigned int offset, int value) { struct aw9523 *awi = gpiochip_get_data(chip); u8 regbit = offset % AW9523_PINS_PER_PORT; int ret; mutex_lock(&awi->i2c_lock); ret = regmap_update_bits(awi->regmap, AW9523_REG_OUT_STATE(offset), BIT(regbit), value ? BIT(regbit) : 0); if (ret) goto end; ret = regmap_update_bits(awi->regmap, AW9523_REG_CONF_STATE(offset), BIT(regbit), 0); end: mutex_unlock(&awi->i2c_lock); return ret; } static int aw9523_drive_reset_gpio(struct aw9523 *awi) { unsigned int chip_id; int ret; /* * If the chip is already configured for any reason, then we * will probably succeed in sending the soft reset signal to * the hardware through I2C: this operation takes less time * compared to a full HW reset and it gives the same results. */ ret = regmap_write(awi->regmap, AW9523_REG_SOFT_RESET, 0); if (ret == 0) goto done; dev_dbg(awi->dev, "Cannot execute soft reset: trying hard reset\n"); ret = gpiod_direction_output(awi->reset_gpio, 0); if (ret) return ret; /* The reset pulse has to be longer than 20uS due to deglitch */ usleep_range(AW9523_HW_RESET_US, AW9523_HW_RESET_US + 1); ret = gpiod_direction_output(awi->reset_gpio, 1); if (ret) return ret; done: /* The HW needs at least 1uS to reliably recover after reset */ usleep_range(AW9523_HW_RESET_RECOVERY_US, AW9523_HW_RESET_RECOVERY_US + 1); /* Check the ChipID */ ret = regmap_read(awi->regmap, AW9523_REG_CHIPID, &chip_id); if (ret) { dev_err(awi->dev, "Cannot read Chip ID: %d\n", ret); return ret; } if (chip_id != AW9523_VAL_EXPECTED_CHIPID) { dev_err(awi->dev, "Bad ChipID; read 0x%x, expected 0x%x\n", chip_id, AW9523_VAL_EXPECTED_CHIPID); return -EINVAL; } return 0; } static int aw9523_hw_reset(struct aw9523 *awi) { int ret, max_retries = 2; /* Sometimes the chip needs more than one reset cycle */ do { ret = aw9523_drive_reset_gpio(awi); if (ret == 0) break; max_retries--; } while (max_retries); return ret; } static int aw9523_init_gpiochip(struct aw9523 *awi, unsigned int npins) { struct device *dev = awi->dev; struct gpio_chip *gc = &awi->gpio; gc->label = devm_kstrdup(dev, dev_name(dev), GFP_KERNEL); if (!gc->label) return -ENOMEM; gc->base = -1; gc->ngpio = npins; gc->get_direction = aw9523_gpio_get_direction; gc->direction_input = aw9523_direction_input; gc->direction_output = aw9523_direction_output; gc->get = aw9523_gpio_get; gc->get_multiple = aw9523_gpio_get_multiple; gc->set = aw9523_gpio_set; gc->set_multiple = aw9523_gpio_set_multiple; gc->set_config = gpiochip_generic_config; gc->parent = dev; gc->owner = THIS_MODULE; gc->can_sleep = false; return 0; } static const struct irq_chip aw9523_irq_chip = { .name = "aw9523", .irq_mask = aw9523_irq_mask, .irq_unmask = aw9523_irq_unmask, .irq_bus_lock = aw9523_irq_bus_lock, .irq_bus_sync_unlock = aw9523_irq_bus_sync_unlock, .irq_set_type = aw9523_gpio_irq_type, .flags = IRQCHIP_IMMUTABLE, GPIOCHIP_IRQ_RESOURCE_HELPERS, }; static int aw9523_init_irq(struct aw9523 *awi, int irq) { struct device *dev = awi->dev; struct gpio_irq_chip *girq; int ret; if (!device_property_read_bool(dev, "interrupt-controller")) return 0; awi->irq = devm_kzalloc(dev, sizeof(*awi->irq), GFP_KERNEL); if (!awi->irq) return -ENOMEM; mutex_init(&awi->irq->lock); ret = devm_request_threaded_irq(dev, irq, NULL, aw9523_irq_thread_func, IRQF_ONESHOT, dev_name(dev), awi); if (ret) return dev_err_probe(dev, ret, "Failed to request irq %d\n", irq); girq = &awi->gpio.irq; gpio_irq_chip_set_chip(girq, &aw9523_irq_chip); girq->parent_handler = NULL; girq->num_parents = 0; girq->parents = NULL; girq->default_type = IRQ_TYPE_EDGE_BOTH; girq->handler = handle_simple_irq; girq->threaded = true; return 0; } static bool aw9523_is_reg_hole(unsigned int reg) { return (reg > AW9523_REG_PORT_MODE(AW9523_PINS_PER_PORT) && reg < AW9523_REG_SOFT_RESET) || (reg > AW9523_REG_INTR_DIS(AW9523_PINS_PER_PORT) && reg < AW9523_REG_CHIPID); } static bool aw9523_readable_reg(struct device *dev, unsigned int reg) { /* All available registers (minus holes) can be read */ return !aw9523_is_reg_hole(reg); } static bool aw9523_volatile_reg(struct device *dev, unsigned int reg) { return aw9523_is_reg_hole(reg) || reg == AW9523_REG_IN_STATE(0) || reg == AW9523_REG_IN_STATE(AW9523_PINS_PER_PORT) || reg == AW9523_REG_CHIPID || reg == AW9523_REG_SOFT_RESET; } static bool aw9523_writeable_reg(struct device *dev, unsigned int reg) { return !aw9523_is_reg_hole(reg) && reg != AW9523_REG_CHIPID; } static bool aw9523_precious_reg(struct device *dev, unsigned int reg) { /* Reading AW9523_REG_IN_STATE clears interrupt status */ return aw9523_is_reg_hole(reg) || reg == AW9523_REG_IN_STATE(0) || reg == AW9523_REG_IN_STATE(AW9523_PINS_PER_PORT); } static const struct regmap_config aw9523_regmap = { .reg_bits = 8, .val_bits = 8, .reg_stride = 1, .precious_reg = aw9523_precious_reg, .readable_reg = aw9523_readable_reg, .volatile_reg = aw9523_volatile_reg, .writeable_reg = aw9523_writeable_reg, .cache_type = REGCACHE_FLAT, .disable_locking = true, .num_reg_defaults_raw = AW9523_REG_SOFT_RESET, }; static int aw9523_hw_init(struct aw9523 *awi) { u8 p1_pin = AW9523_PINS_PER_PORT; unsigned int val; int ret; /* No register caching during initialization */ regcache_cache_bypass(awi->regmap, true); /* Bring up the chip */ ret = aw9523_hw_reset(awi); if (ret) { dev_err(awi->dev, "HW Reset failed: %d\n", ret); return ret; } /* * This is the expected chip and it is running: it's time to * set a safe default configuration in case the user doesn't * configure (all of the available) pins in this chip. * P.S.: The writes order doesn't matter. */ /* Set all pins as GPIO */ ret = regmap_write(awi->regmap, AW9523_REG_PORT_MODE(0), U8_MAX); if (ret) return ret; ret = regmap_write(awi->regmap, AW9523_REG_PORT_MODE(p1_pin), U8_MAX); if (ret) return ret; /* Set Open-Drain mode on Port 0 (Port 1 is always P-P) */ ret = regmap_write(awi->regmap, AW9523_REG_GCR, 0); if (ret) return ret; /* Set all pins as inputs */ ret = regmap_write(awi->regmap, AW9523_REG_CONF_STATE(0), U8_MAX); if (ret) return ret; ret = regmap_write(awi->regmap, AW9523_REG_CONF_STATE(p1_pin), U8_MAX); if (ret) return ret; /* Disable all interrupts to avoid unreasoned wakeups */ ret = regmap_write(awi->regmap, AW9523_REG_INTR_DIS(0), U8_MAX); if (ret) return ret; ret = regmap_write(awi->regmap, AW9523_REG_INTR_DIS(p1_pin), U8_MAX); if (ret) return ret; /* Clear setup-generated interrupts by performing a port state read */ ret = aw9523_get_port_state(awi->regmap, 0, 0, &val); if (ret) return ret; ret = aw9523_get_port_state(awi->regmap, p1_pin, 0, &val); if (ret) return ret; /* Everything went fine: activate and reinitialize register cache */ regcache_cache_bypass(awi->regmap, false); return regmap_reinit_cache(awi->regmap, &aw9523_regmap); } static int aw9523_probe(struct i2c_client *client) { struct device *dev = &client->dev; struct pinctrl_desc *pdesc; struct aw9523 *awi; int ret; awi = devm_kzalloc(dev, sizeof(*awi), GFP_KERNEL); if (!awi) return -ENOMEM; i2c_set_clientdata(client, awi); awi->dev = dev; awi->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); if (IS_ERR(awi->reset_gpio)) return PTR_ERR(awi->reset_gpio); gpiod_set_consumer_name(awi->reset_gpio, "aw9523 reset"); awi->regmap = devm_regmap_init_i2c(client, &aw9523_regmap); if (IS_ERR(awi->regmap)) return PTR_ERR(awi->regmap); awi->vio_vreg = devm_regulator_get_enable_optional(dev, "vio"); if (awi->vio_vreg && awi->vio_vreg != -ENODEV) return awi->vio_vreg; ret = devm_mutex_init(dev, &awi->i2c_lock); if (ret) return ret; lockdep_set_subclass(&awi->i2c_lock, i2c_adapter_depth(client->adapter)); pdesc = devm_kzalloc(dev, sizeof(*pdesc), GFP_KERNEL); if (!pdesc) return -ENOMEM; ret = aw9523_hw_init(awi); if (ret) return ret; pdesc->name = dev_name(dev); pdesc->owner = THIS_MODULE; pdesc->pctlops = &aw9523_pinctrl_ops; pdesc->pmxops = &aw9523_pinmux_ops; pdesc->confops = &aw9523_pinconf_ops; pdesc->pins = aw9523_pins; pdesc->npins = ARRAY_SIZE(aw9523_pins); ret = aw9523_init_gpiochip(awi, pdesc->npins); if (ret) return ret; if (client->irq) { ret = aw9523_init_irq(awi, client->irq); if (ret) return ret; } awi->pctl = devm_pinctrl_register(dev, pdesc, awi); if (IS_ERR(awi->pctl)) return dev_err_probe(dev, PTR_ERR(awi->pctl), "Cannot register pinctrl"); return devm_gpiochip_add_data(dev, &awi->gpio, awi); } static void aw9523_remove(struct i2c_client *client) { struct aw9523 *awi = i2c_get_clientdata(client); /* * If the chip VIO is connected to a regulator that we can turn * off, life is easy... otherwise, reinitialize the chip and * set the pins to hardware defaults before removing the driver * to leave it in a clean, safe and predictable state. */ if (awi->vio_vreg == -ENODEV) { mutex_lock(&awi->i2c_lock); aw9523_hw_init(awi); mutex_unlock(&awi->i2c_lock); } } static const struct i2c_device_id aw9523_i2c_id_table[] = { { "aw9523_i2c" }, { } }; MODULE_DEVICE_TABLE(i2c, aw9523_i2c_id_table); static const struct of_device_id of_aw9523_i2c_match[] = { { .compatible = "awinic,aw9523-pinctrl", }, { } }; MODULE_DEVICE_TABLE(of, of_aw9523_i2c_match); static struct i2c_driver aw9523_driver = { .driver = { .name = "aw9523-pinctrl", .of_match_table = of_aw9523_i2c_match, }, .probe = aw9523_probe, .remove = aw9523_remove, .id_table = aw9523_i2c_id_table, }; module_i2c_driver(aw9523_driver); MODULE_DESCRIPTION("Awinic AW9523 I2C GPIO Expander driver"); MODULE_AUTHOR("AngeloGioacchino Del Regno "); MODULE_LICENSE("GPL v2");