.. SPDX-License-Identifier: GPL-2.0 .. _transmitter-receiver: Pixel data transmitter and receiver drivers =========================================== V4L2 supports various devices that transmit and receive pixel data. Examples of these devices include a camera sensor, a TV tuner and a parallel, a BT.656 or a CSI-2 receiver in an SoC. Bus types --------- The following busses are the most common. This section discusses these two only. MIPI CSI-2 ^^^^^^^^^^ CSI-2 is a data bus intended for transferring images from cameras to the host SoC. It is defined by the `MIPI alliance`_. .. _`MIPI alliance`: https://www.mipi.org/ Parallel and BT.656 ^^^^^^^^^^^^^^^^^^^ The parallel and `BT.656`_ buses transport one bit of data on each clock cycle per data line. The parallel bus uses synchronisation and other additional signals whereas BT.656 embeds synchronisation. .. _`BT.656`: https://en.wikipedia.org/wiki/ITU-R_BT.656 Transmitter drivers ------------------- Transmitter drivers generally need to provide the receiver drivers with the configuration of the transmitter. What is required depends on the type of the bus. These are common for both busses. Media bus pixel code ^^^^^^^^^^^^^^^^^^^^ See :ref:`v4l2-mbus-pixelcode`. Link frequency ^^^^^^^^^^^^^^ The :ref:`V4L2_CID_LINK_FREQ ` control is used to tell the receiver the frequency of the bus (i.e. it is not the same as the symbol rate). ``.enable_streams()`` and ``.disable_streams()`` callbacks ^^^^^^^^^^^^^^^^^^^^^^^^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The struct v4l2_subdev_pad_ops->enable_streams() and struct v4l2_subdev_pad_ops->disable_streams() callbacks are used by the receiver driver to control the transmitter driver's streaming state. These callbacks may not be called directly, but by using ``v4l2_subdev_enable_streams()`` and ``v4l2_subdev_disable_streams()``. CSI-2 transmitter drivers ------------------------- Pixel rate ^^^^^^^^^^ The pixel rate on the bus is calculated as follows:: pixel_rate = link_freq * 2 * nr_of_lanes * 16 / k / bits_per_sample where .. list-table:: variables in pixel rate calculation :header-rows: 1 * - variable or constant - description * - link_freq - The value of the ``V4L2_CID_LINK_FREQ`` integer64 menu item. * - nr_of_lanes - Number of data lanes used on the CSI-2 link. This can be obtained from the OF endpoint configuration. * - 2 - Data is transferred on both rising and falling edge of the signal. * - bits_per_sample - Number of bits per sample. * - k - 16 for D-PHY and 7 for C-PHY .. note:: The pixel rate calculated this way is **not** the same thing as the pixel rate on the camera sensor's pixel array which is indicated by the :ref:`V4L2_CID_PIXEL_RATE ` control. LP-11 and LP-111 states ^^^^^^^^^^^^^^^^^^^^^^^ As part of transitioning to high speed mode, a CSI-2 transmitter typically briefly sets the bus to LP-11 or LP-111 state, depending on the PHY. This period may be as short as 100 µs, during which the receiver observes this state and proceeds its own part of high speed mode transition. Most receivers are capable of autonomously handling this once the software has configured them to do so, but there are receivers which require software involvement in observing LP-11 or LP-111 state. 100 µs is a brief period to hit in software, especially when there is no interrupt telling something is happening. One way to address this is to configure the transmitter side explicitly to LP-11 or LP-111 state, which requires support from the transmitter hardware. This is not universally available. Many devices return to this state once streaming is stopped while the state after power-on is LP-00 or LP-000. The ``.pre_streamon()`` callback may be used to prepare a transmitter for transitioning to streaming state, but not yet start streaming. Similarly, the ``.post_streamoff()`` callback is used to undo what was done by the ``.pre_streamon()`` callback. The caller of ``.pre_streamon()`` is thus required to call ``.post_streamoff()`` for each successful call of ``.pre_streamon()``. In the context of CSI-2, the ``.pre_streamon()`` callback is used to transition the transmitter to the LP-11 or LP-111 state. This also requires powering on the device, so this should be only done when it is needed. Receiver drivers that do not need explicit LP-11 or LP-111 state setup are waived from calling the two callbacks. Stopping the transmitter ^^^^^^^^^^^^^^^^^^^^^^^^ A transmitter stops sending the stream of images as a result of calling the ``.disable_streams()`` callback. Some transmitters may stop the stream at a frame boundary whereas others stop immediately, effectively leaving the current frame unfinished. The receiver driver should not make assumptions either way, but function properly in both cases.