// SPDX-License-Identifier: GPL-2.0 /* * Renesas RIIC driver * * Copyright (C) 2013 Wolfram Sang * Copyright (C) 2013 Renesas Solutions Corp. */ /* * This i2c core has a lot of interrupts, namely 8. We use their chaining as * some kind of state machine. * * 1) The main xfer routine kicks off a transmission by putting the start bit * (or repeated start) on the bus and enabling the transmit interrupt (TIE) * since we need to send the target address + RW bit in every case. * * 2) TIE sends target address + RW bit and selects how to continue. * * 3a) Write case: We keep utilizing TIE as long as we have data to send. If we * are done, we switch over to the transmission done interrupt (TEIE) and mark * the message as completed (includes sending STOP) there. * * 3b) Read case: We switch over to receive interrupt (RIE). One dummy read is * needed to start clocking, then we keep receiving until we are done. Note * that we use the RDRFS mode all the time, i.e. we ACK/NACK every byte by * writing to the ACKBT bit. I tried using the RDRFS mode only at the end of a * message to create the final NACK as sketched in the datasheet. This caused * some subtle races (when byte n was processed and byte n+1 was already * waiting), though, and I started with the safe approach. * * 4) If we got a NACK somewhere, we flag the error and stop the transmission * via NAKIE. * * Also check the comments in the interrupt routines for some gory details. */ #include #include #include #include #include #include #include #include #include #include #include #define ICCR1_ICE 0x80 #define ICCR1_IICRST 0x40 #define ICCR1_SOWP 0x10 #define ICCR2_BBSY 0x80 #define ICCR2_SP 0x08 #define ICCR2_RS 0x04 #define ICCR2_ST 0x02 #define ICMR1_CKS_MASK 0x70 #define ICMR1_BCWP 0x08 #define ICMR1_CKS(_x) ((((_x) << 4) & ICMR1_CKS_MASK) | ICMR1_BCWP) #define ICMR3_RDRFS 0x20 #define ICMR3_ACKWP 0x10 #define ICMR3_ACKBT 0x08 #define ICFER_FMPE 0x80 #define ICIER_TIE 0x80 #define ICIER_TEIE 0x40 #define ICIER_RIE 0x20 #define ICIER_NAKIE 0x10 #define ICIER_SPIE 0x08 #define ICSR2_NACKF 0x10 #define ICBR_RESERVED 0xe0 /* Should be 1 on writes */ #define RIIC_INIT_MSG -1 enum riic_reg_list { RIIC_ICCR1 = 0, RIIC_ICCR2, RIIC_ICMR1, RIIC_ICMR3, RIIC_ICFER, RIIC_ICSER, RIIC_ICIER, RIIC_ICSR2, RIIC_ICBRL, RIIC_ICBRH, RIIC_ICDRT, RIIC_ICDRR, RIIC_REG_END, }; struct riic_of_data { const u8 *regs; bool fast_mode_plus; }; struct riic_dev { void __iomem *base; u8 *buf; struct i2c_msg *msg; int bytes_left; int err; int is_last; const struct riic_of_data *info; struct completion msg_done; struct i2c_adapter adapter; struct clk *clk; struct reset_control *rstc; struct i2c_timings i2c_t; }; struct riic_irq_desc { int res_num; irq_handler_t isr; char *name; }; static inline void riic_writeb(struct riic_dev *riic, u8 val, u8 offset) { writeb(val, riic->base + riic->info->regs[offset]); } static inline u8 riic_readb(struct riic_dev *riic, u8 offset) { return readb(riic->base + riic->info->regs[offset]); } static inline void riic_clear_set_bit(struct riic_dev *riic, u8 clear, u8 set, u8 reg) { riic_writeb(riic, (riic_readb(riic, reg) & ~clear) | set, reg); } static int riic_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) { struct riic_dev *riic = i2c_get_adapdata(adap); struct device *dev = adap->dev.parent; unsigned long time_left; int i, ret; u8 start_bit; ret = pm_runtime_resume_and_get(dev); if (ret) return ret; if (riic_readb(riic, RIIC_ICCR2) & ICCR2_BBSY) { riic->err = -EBUSY; goto out; } reinit_completion(&riic->msg_done); riic->err = 0; riic_writeb(riic, 0, RIIC_ICSR2); for (i = 0, start_bit = ICCR2_ST; i < num; i++) { riic->bytes_left = RIIC_INIT_MSG; riic->buf = msgs[i].buf; riic->msg = &msgs[i]; riic->is_last = (i == num - 1); riic_writeb(riic, ICIER_NAKIE | ICIER_TIE, RIIC_ICIER); riic_writeb(riic, start_bit, RIIC_ICCR2); time_left = wait_for_completion_timeout(&riic->msg_done, riic->adapter.timeout); if (time_left == 0) riic->err = -ETIMEDOUT; if (riic->err) break; start_bit = ICCR2_RS; } out: pm_runtime_mark_last_busy(dev); pm_runtime_put_autosuspend(dev); return riic->err ?: num; } static irqreturn_t riic_tdre_isr(int irq, void *data) { struct riic_dev *riic = data; u8 val; if (!riic->bytes_left) return IRQ_NONE; if (riic->bytes_left == RIIC_INIT_MSG) { if (riic->msg->flags & I2C_M_RD) /* On read, switch over to receive interrupt */ riic_clear_set_bit(riic, ICIER_TIE, ICIER_RIE, RIIC_ICIER); else /* On write, initialize length */ riic->bytes_left = riic->msg->len; val = i2c_8bit_addr_from_msg(riic->msg); } else { val = *riic->buf; riic->buf++; riic->bytes_left--; } /* * Switch to transmission ended interrupt when done. Do check here * after bytes_left was initialized to support SMBUS_QUICK (new msg has * 0 length then) */ if (riic->bytes_left == 0) riic_clear_set_bit(riic, ICIER_TIE, ICIER_TEIE, RIIC_ICIER); /* * This acks the TIE interrupt. We get another TIE immediately if our * value could be moved to the shadow shift register right away. So * this must be after updates to ICIER (where we want to disable TIE)! */ riic_writeb(riic, val, RIIC_ICDRT); return IRQ_HANDLED; } static irqreturn_t riic_tend_isr(int irq, void *data) { struct riic_dev *riic = data; if (riic_readb(riic, RIIC_ICSR2) & ICSR2_NACKF) { /* We got a NACKIE */ riic_readb(riic, RIIC_ICDRR); /* dummy read */ riic_clear_set_bit(riic, ICSR2_NACKF, 0, RIIC_ICSR2); riic->err = -ENXIO; } else if (riic->bytes_left) { return IRQ_NONE; } if (riic->is_last || riic->err) { riic_clear_set_bit(riic, ICIER_TEIE, ICIER_SPIE, RIIC_ICIER); riic_writeb(riic, ICCR2_SP, RIIC_ICCR2); } else { /* Transfer is complete, but do not send STOP */ riic_clear_set_bit(riic, ICIER_TEIE, 0, RIIC_ICIER); complete(&riic->msg_done); } return IRQ_HANDLED; } static irqreturn_t riic_rdrf_isr(int irq, void *data) { struct riic_dev *riic = data; if (!riic->bytes_left) return IRQ_NONE; if (riic->bytes_left == RIIC_INIT_MSG) { riic->bytes_left = riic->msg->len; riic_readb(riic, RIIC_ICDRR); /* dummy read */ return IRQ_HANDLED; } if (riic->bytes_left == 1) { /* STOP must come before we set ACKBT! */ if (riic->is_last) { riic_clear_set_bit(riic, 0, ICIER_SPIE, RIIC_ICIER); riic_writeb(riic, ICCR2_SP, RIIC_ICCR2); } riic_clear_set_bit(riic, 0, ICMR3_ACKBT, RIIC_ICMR3); } else { riic_clear_set_bit(riic, ICMR3_ACKBT, 0, RIIC_ICMR3); } /* Reading acks the RIE interrupt */ *riic->buf = riic_readb(riic, RIIC_ICDRR); riic->buf++; riic->bytes_left--; return IRQ_HANDLED; } static irqreturn_t riic_stop_isr(int irq, void *data) { struct riic_dev *riic = data; /* read back registers to confirm writes have fully propagated */ riic_writeb(riic, 0, RIIC_ICSR2); riic_readb(riic, RIIC_ICSR2); riic_writeb(riic, 0, RIIC_ICIER); riic_readb(riic, RIIC_ICIER); complete(&riic->msg_done); return IRQ_HANDLED; } static u32 riic_func(struct i2c_adapter *adap) { return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; } static const struct i2c_algorithm riic_algo = { .xfer = riic_xfer, .functionality = riic_func, }; static int riic_init_hw(struct riic_dev *riic) { int ret; unsigned long rate; int total_ticks, cks, brl, brh; struct i2c_timings *t = &riic->i2c_t; struct device *dev = riic->adapter.dev.parent; bool fast_mode_plus = riic->info->fast_mode_plus; u32 max_freq = fast_mode_plus ? I2C_MAX_FAST_MODE_PLUS_FREQ : I2C_MAX_FAST_MODE_FREQ; if (t->bus_freq_hz > max_freq) return dev_err_probe(&riic->adapter.dev, -EINVAL, "unsupported bus speed %uHz (%u max)\n", t->bus_freq_hz, max_freq); rate = clk_get_rate(riic->clk); /* * Assume the default register settings: * FER.SCLE = 1 (SCL sync circuit enabled, adds 2 or 3 cycles) * FER.NFE = 1 (noise circuit enabled) * MR3.NF = 0 (1 cycle of noise filtered out) * * Freq (CKS=000) = (I2CCLK + tr + tf)/ (BRH + 3 + 1) + (BRL + 3 + 1) * Freq (CKS!=000) = (I2CCLK + tr + tf)/ (BRH + 2 + 1) + (BRL + 2 + 1) */ /* * Determine reference clock rate. We must be able to get the desired * frequency with only 62 clock ticks max (31 high, 31 low). * Aim for a duty of 60% LOW, 40% HIGH. */ total_ticks = DIV_ROUND_UP(rate, t->bus_freq_hz ?: 1); for (cks = 0; cks < 7; cks++) { /* * 60% low time must be less than BRL + 2 + 1 * BRL max register value is 0x1F. */ brl = ((total_ticks * 6) / 10); if (brl <= (0x1F + 3)) break; total_ticks = DIV_ROUND_UP(total_ticks, 2); rate /= 2; } if (brl > (0x1F + 3)) { dev_err(&riic->adapter.dev, "invalid speed (%lu). Too slow.\n", (unsigned long)t->bus_freq_hz); return -EINVAL; } brh = total_ticks - brl; /* Remove automatic clock ticks for sync circuit and NF */ if (cks == 0) { brl -= 4; brh -= 4; } else { brl -= 3; brh -= 3; } /* * Remove clock ticks for rise and fall times. Convert ns to clock * ticks. */ brl -= t->scl_fall_ns / (1000000000 / rate); brh -= t->scl_rise_ns / (1000000000 / rate); /* Adjust for min register values for when SCLE=1 and NFE=1 */ if (brl < 1) brl = 1; if (brh < 1) brh = 1; pr_debug("i2c-riic: freq=%lu, duty=%d, fall=%lu, rise=%lu, cks=%d, brl=%d, brh=%d\n", rate / total_ticks, ((brl + 3) * 100) / (brl + brh + 6), t->scl_fall_ns / (1000000000 / rate), t->scl_rise_ns / (1000000000 / rate), cks, brl, brh); ret = pm_runtime_resume_and_get(dev); if (ret) return ret; /* Changing the order of accessing IICRST and ICE may break things! */ riic_writeb(riic, ICCR1_IICRST | ICCR1_SOWP, RIIC_ICCR1); riic_clear_set_bit(riic, 0, ICCR1_ICE, RIIC_ICCR1); riic_writeb(riic, ICMR1_CKS(cks), RIIC_ICMR1); riic_writeb(riic, brh | ICBR_RESERVED, RIIC_ICBRH); riic_writeb(riic, brl | ICBR_RESERVED, RIIC_ICBRL); riic_writeb(riic, 0, RIIC_ICSER); riic_writeb(riic, ICMR3_ACKWP | ICMR3_RDRFS, RIIC_ICMR3); if (fast_mode_plus && t->bus_freq_hz > I2C_MAX_FAST_MODE_FREQ) riic_clear_set_bit(riic, 0, ICFER_FMPE, RIIC_ICFER); riic_clear_set_bit(riic, ICCR1_IICRST, 0, RIIC_ICCR1); pm_runtime_mark_last_busy(dev); pm_runtime_put_autosuspend(dev); return 0; } static struct riic_irq_desc riic_irqs[] = { { .res_num = 0, .isr = riic_tend_isr, .name = "riic-tend" }, { .res_num = 1, .isr = riic_rdrf_isr, .name = "riic-rdrf" }, { .res_num = 2, .isr = riic_tdre_isr, .name = "riic-tdre" }, { .res_num = 3, .isr = riic_stop_isr, .name = "riic-stop" }, { .res_num = 5, .isr = riic_tend_isr, .name = "riic-nack" }, }; static void riic_reset_control_assert(void *data) { reset_control_assert(data); } static int riic_i2c_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct riic_dev *riic; struct i2c_adapter *adap; int i, ret; riic = devm_kzalloc(dev, sizeof(*riic), GFP_KERNEL); if (!riic) return -ENOMEM; riic->base = devm_platform_ioremap_resource(pdev, 0); if (IS_ERR(riic->base)) return PTR_ERR(riic->base); riic->clk = devm_clk_get(dev, NULL); if (IS_ERR(riic->clk)) { dev_err(dev, "missing controller clock"); return PTR_ERR(riic->clk); } riic->rstc = devm_reset_control_get_optional_exclusive(dev, NULL); if (IS_ERR(riic->rstc)) return dev_err_probe(dev, PTR_ERR(riic->rstc), "Error: missing reset ctrl\n"); ret = reset_control_deassert(riic->rstc); if (ret) return ret; ret = devm_add_action_or_reset(dev, riic_reset_control_assert, riic->rstc); if (ret) return ret; for (i = 0; i < ARRAY_SIZE(riic_irqs); i++) { ret = platform_get_irq(pdev, riic_irqs[i].res_num); if (ret < 0) return ret; ret = devm_request_irq(dev, ret, riic_irqs[i].isr, 0, riic_irqs[i].name, riic); if (ret) { dev_err(dev, "failed to request irq %s\n", riic_irqs[i].name); return ret; } } riic->info = of_device_get_match_data(dev); adap = &riic->adapter; i2c_set_adapdata(adap, riic); strscpy(adap->name, "Renesas RIIC adapter", sizeof(adap->name)); adap->owner = THIS_MODULE; adap->algo = &riic_algo; adap->dev.parent = dev; adap->dev.of_node = dev->of_node; init_completion(&riic->msg_done); i2c_parse_fw_timings(dev, &riic->i2c_t, true); /* Default 0 to save power. Can be overridden via sysfs for lower latency. */ pm_runtime_set_autosuspend_delay(dev, 0); pm_runtime_use_autosuspend(dev); pm_runtime_enable(dev); ret = riic_init_hw(riic); if (ret) goto out; ret = i2c_add_adapter(adap); if (ret) goto out; platform_set_drvdata(pdev, riic); dev_info(dev, "registered with %dHz bus speed\n", riic->i2c_t.bus_freq_hz); return 0; out: pm_runtime_disable(dev); pm_runtime_dont_use_autosuspend(dev); return ret; } static void riic_i2c_remove(struct platform_device *pdev) { struct riic_dev *riic = platform_get_drvdata(pdev); struct device *dev = &pdev->dev; int ret; ret = pm_runtime_resume_and_get(dev); if (!ret) { riic_writeb(riic, 0, RIIC_ICIER); pm_runtime_put(dev); } i2c_del_adapter(&riic->adapter); pm_runtime_disable(dev); pm_runtime_dont_use_autosuspend(dev); } static const u8 riic_rz_a_regs[RIIC_REG_END] = { [RIIC_ICCR1] = 0x00, [RIIC_ICCR2] = 0x04, [RIIC_ICMR1] = 0x08, [RIIC_ICMR3] = 0x10, [RIIC_ICFER] = 0x14, [RIIC_ICSER] = 0x18, [RIIC_ICIER] = 0x1c, [RIIC_ICSR2] = 0x24, [RIIC_ICBRL] = 0x34, [RIIC_ICBRH] = 0x38, [RIIC_ICDRT] = 0x3c, [RIIC_ICDRR] = 0x40, }; static const struct riic_of_data riic_rz_a_info = { .regs = riic_rz_a_regs, .fast_mode_plus = true, }; static const struct riic_of_data riic_rz_a1h_info = { .regs = riic_rz_a_regs, }; static const u8 riic_rz_v2h_regs[RIIC_REG_END] = { [RIIC_ICCR1] = 0x00, [RIIC_ICCR2] = 0x01, [RIIC_ICMR1] = 0x02, [RIIC_ICMR3] = 0x04, [RIIC_ICFER] = 0x05, [RIIC_ICSER] = 0x06, [RIIC_ICIER] = 0x07, [RIIC_ICSR2] = 0x09, [RIIC_ICBRL] = 0x10, [RIIC_ICBRH] = 0x11, [RIIC_ICDRT] = 0x12, [RIIC_ICDRR] = 0x13, }; static const struct riic_of_data riic_rz_v2h_info = { .regs = riic_rz_v2h_regs, .fast_mode_plus = true, }; static int riic_i2c_suspend(struct device *dev) { struct riic_dev *riic = dev_get_drvdata(dev); int ret; ret = pm_runtime_resume_and_get(dev); if (ret) return ret; i2c_mark_adapter_suspended(&riic->adapter); /* Disable output on SDA, SCL pins. */ riic_clear_set_bit(riic, ICCR1_ICE, 0, RIIC_ICCR1); pm_runtime_mark_last_busy(dev); pm_runtime_put_sync(dev); return reset_control_assert(riic->rstc); } static int riic_i2c_resume(struct device *dev) { struct riic_dev *riic = dev_get_drvdata(dev); int ret; ret = reset_control_deassert(riic->rstc); if (ret) return ret; ret = riic_init_hw(riic); if (ret) { /* * In case this happens there is no way to recover from this * state. The driver will remain loaded. We want to avoid * keeping the reset line de-asserted for no reason. */ reset_control_assert(riic->rstc); return ret; } i2c_mark_adapter_resumed(&riic->adapter); return 0; } static const struct dev_pm_ops riic_i2c_pm_ops = { SYSTEM_SLEEP_PM_OPS(riic_i2c_suspend, riic_i2c_resume) }; static const struct of_device_id riic_i2c_dt_ids[] = { { .compatible = "renesas,riic-rz", .data = &riic_rz_a_info }, { .compatible = "renesas,riic-r7s72100", .data = &riic_rz_a1h_info, }, { .compatible = "renesas,riic-r9a09g057", .data = &riic_rz_v2h_info }, { /* Sentinel */ }, }; static struct platform_driver riic_i2c_driver = { .probe = riic_i2c_probe, .remove = riic_i2c_remove, .driver = { .name = "i2c-riic", .of_match_table = riic_i2c_dt_ids, .pm = pm_ptr(&riic_i2c_pm_ops), }, }; module_platform_driver(riic_i2c_driver); MODULE_DESCRIPTION("Renesas RIIC adapter"); MODULE_AUTHOR("Wolfram Sang "); MODULE_LICENSE("GPL v2"); MODULE_DEVICE_TABLE(of, riic_i2c_dt_ids);