/** * \file * * \brief Instance description for SERCOM7 * * Copyright (c) 2018 Microchip Technology Inc. * * \asf_license_start * * \page License * * SPDX-License-Identifier: Apache-2.0 * * Licensed under the Apache License, Version 2.0 (the "License"); you may * not use this file except in compliance with the License. * You may obtain a copy of the Licence at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an AS IS BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * * \asf_license_stop * */ #ifndef _SAME54_SERCOM7_INSTANCE_ #define _SAME54_SERCOM7_INSTANCE_ /* ========== Register definition for SERCOM7 peripheral ========== */ #if (defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) #define REG_SERCOM7_I2CM_CTRLA (0x43000C00) /**< \brief (SERCOM7) I2CM Control A */ #define REG_SERCOM7_I2CM_CTRLB (0x43000C04) /**< \brief (SERCOM7) I2CM Control B */ #define REG_SERCOM7_I2CM_CTRLC (0x43000C08) /**< \brief (SERCOM7) I2CM Control C */ #define REG_SERCOM7_I2CM_BAUD (0x43000C0C) /**< \brief (SERCOM7) I2CM Baud Rate */ #define REG_SERCOM7_I2CM_INTENCLR (0x43000C14) /**< \brief (SERCOM7) I2CM Interrupt Enable Clear */ #define REG_SERCOM7_I2CM_INTENSET (0x43000C16) /**< \brief (SERCOM7) I2CM Interrupt Enable Set */ #define REG_SERCOM7_I2CM_INTFLAG (0x43000C18) /**< \brief (SERCOM7) I2CM Interrupt Flag Status and Clear */ #define REG_SERCOM7_I2CM_STATUS (0x43000C1A) /**< \brief (SERCOM7) I2CM Status */ #define REG_SERCOM7_I2CM_SYNCBUSY (0x43000C1C) /**< \brief (SERCOM7) I2CM Synchronization Busy */ #define REG_SERCOM7_I2CM_ADDR (0x43000C24) /**< \brief (SERCOM7) I2CM Address */ #define REG_SERCOM7_I2CM_DATA (0x43000C28) /**< \brief (SERCOM7) I2CM Data */ #define REG_SERCOM7_I2CM_DBGCTRL (0x43000C30) /**< \brief (SERCOM7) I2CM Debug Control */ #define REG_SERCOM7_I2CS_CTRLA (0x43000C00) /**< \brief (SERCOM7) I2CS Control A */ #define REG_SERCOM7_I2CS_CTRLB (0x43000C04) /**< \brief (SERCOM7) I2CS Control B */ #define REG_SERCOM7_I2CS_CTRLC (0x43000C08) /**< \brief (SERCOM7) I2CS Control C */ #define REG_SERCOM7_I2CS_INTENCLR (0x43000C14) /**< \brief (SERCOM7) I2CS Interrupt Enable Clear */ #define REG_SERCOM7_I2CS_INTENSET (0x43000C16) /**< \brief (SERCOM7) I2CS Interrupt Enable Set */ #define REG_SERCOM7_I2CS_INTFLAG (0x43000C18) /**< \brief (SERCOM7) I2CS Interrupt Flag Status and Clear */ #define REG_SERCOM7_I2CS_STATUS (0x43000C1A) /**< \brief (SERCOM7) I2CS Status */ #define REG_SERCOM7_I2CS_SYNCBUSY (0x43000C1C) /**< \brief (SERCOM7) I2CS Synchronization Busy */ #define REG_SERCOM7_I2CS_LENGTH (0x43000C22) /**< \brief (SERCOM7) I2CS Length */ #define REG_SERCOM7_I2CS_ADDR (0x43000C24) /**< \brief (SERCOM7) I2CS Address */ #define REG_SERCOM7_I2CS_DATA (0x43000C28) /**< \brief (SERCOM7) I2CS Data */ #define REG_SERCOM7_SPI_CTRLA (0x43000C00) /**< \brief (SERCOM7) SPI Control A */ #define REG_SERCOM7_SPI_CTRLB (0x43000C04) /**< \brief (SERCOM7) SPI Control B */ #define REG_SERCOM7_SPI_CTRLC (0x43000C08) /**< \brief (SERCOM7) SPI Control C */ #define REG_SERCOM7_SPI_BAUD (0x43000C0C) /**< \brief (SERCOM7) SPI Baud Rate */ #define REG_SERCOM7_SPI_INTENCLR (0x43000C14) /**< \brief (SERCOM7) SPI Interrupt Enable Clear */ #define REG_SERCOM7_SPI_INTENSET (0x43000C16) /**< \brief (SERCOM7) SPI Interrupt Enable Set */ #define REG_SERCOM7_SPI_INTFLAG (0x43000C18) /**< \brief (SERCOM7) SPI Interrupt Flag Status and Clear */ #define REG_SERCOM7_SPI_STATUS (0x43000C1A) /**< \brief (SERCOM7) SPI Status */ #define REG_SERCOM7_SPI_SYNCBUSY (0x43000C1C) /**< \brief (SERCOM7) SPI Synchronization Busy */ #define REG_SERCOM7_SPI_LENGTH (0x43000C22) /**< \brief (SERCOM7) SPI Length */ #define REG_SERCOM7_SPI_ADDR (0x43000C24) /**< \brief (SERCOM7) SPI Address */ #define REG_SERCOM7_SPI_DATA (0x43000C28) /**< \brief (SERCOM7) SPI Data */ #define REG_SERCOM7_SPI_DBGCTRL (0x43000C30) /**< \brief (SERCOM7) SPI Debug Control */ #define REG_SERCOM7_USART_CTRLA (0x43000C00) /**< \brief (SERCOM7) USART Control A */ #define REG_SERCOM7_USART_CTRLB (0x43000C04) /**< \brief (SERCOM7) USART Control B */ #define REG_SERCOM7_USART_CTRLC (0x43000C08) /**< \brief (SERCOM7) USART Control C */ #define REG_SERCOM7_USART_BAUD (0x43000C0C) /**< \brief (SERCOM7) USART Baud Rate */ #define REG_SERCOM7_USART_RXPL (0x43000C0E) /**< \brief (SERCOM7) USART Receive Pulse Length */ #define REG_SERCOM7_USART_INTENCLR (0x43000C14) /**< \brief (SERCOM7) USART Interrupt Enable Clear */ #define REG_SERCOM7_USART_INTENSET (0x43000C16) /**< \brief (SERCOM7) USART Interrupt Enable Set */ #define REG_SERCOM7_USART_INTFLAG (0x43000C18) /**< \brief (SERCOM7) USART Interrupt Flag Status and Clear */ #define REG_SERCOM7_USART_STATUS (0x43000C1A) /**< \brief (SERCOM7) USART Status */ #define REG_SERCOM7_USART_SYNCBUSY (0x43000C1C) /**< \brief (SERCOM7) USART Synchronization Busy */ #define REG_SERCOM7_USART_RXERRCNT (0x43000C20) /**< \brief (SERCOM7) USART Receive Error Count */ #define REG_SERCOM7_USART_LENGTH (0x43000C22) /**< \brief (SERCOM7) USART Length */ #define REG_SERCOM7_USART_DATA (0x43000C28) /**< \brief (SERCOM7) USART Data */ #define REG_SERCOM7_USART_DBGCTRL (0x43000C30) /**< \brief (SERCOM7) USART Debug Control */ #else #define REG_SERCOM7_I2CM_CTRLA (*(RwReg *)0x43000C00UL) /**< \brief (SERCOM7) I2CM Control A */ #define REG_SERCOM7_I2CM_CTRLB (*(RwReg *)0x43000C04UL) /**< \brief (SERCOM7) I2CM Control B */ #define REG_SERCOM7_I2CM_CTRLC (*(RwReg *)0x43000C08UL) /**< \brief (SERCOM7) I2CM Control C */ #define REG_SERCOM7_I2CM_BAUD (*(RwReg *)0x43000C0CUL) /**< \brief (SERCOM7) I2CM Baud Rate */ #define REG_SERCOM7_I2CM_INTENCLR (*(RwReg8 *)0x43000C14UL) /**< \brief (SERCOM7) I2CM Interrupt Enable Clear */ #define REG_SERCOM7_I2CM_INTENSET (*(RwReg8 *)0x43000C16UL) /**< \brief (SERCOM7) I2CM Interrupt Enable Set */ #define REG_SERCOM7_I2CM_INTFLAG (*(RwReg8 *)0x43000C18UL) /**< \brief (SERCOM7) I2CM Interrupt Flag Status and Clear */ #define REG_SERCOM7_I2CM_STATUS (*(RwReg16*)0x43000C1AUL) /**< \brief (SERCOM7) I2CM Status */ #define REG_SERCOM7_I2CM_SYNCBUSY (*(RoReg *)0x43000C1CUL) /**< \brief (SERCOM7) I2CM Synchronization Busy */ #define REG_SERCOM7_I2CM_ADDR (*(RwReg *)0x43000C24UL) /**< \brief (SERCOM7) I2CM Address */ #define REG_SERCOM7_I2CM_DATA (*(RwReg *)0x43000C28UL) /**< \brief (SERCOM7) I2CM Data */ #define REG_SERCOM7_I2CM_DBGCTRL (*(RwReg8 *)0x43000C30UL) /**< \brief (SERCOM7) I2CM Debug Control */ #define REG_SERCOM7_I2CS_CTRLA (*(RwReg *)0x43000C00UL) /**< \brief (SERCOM7) I2CS Control A */ #define REG_SERCOM7_I2CS_CTRLB (*(RwReg *)0x43000C04UL) /**< \brief (SERCOM7) I2CS Control B */ #define REG_SERCOM7_I2CS_CTRLC (*(RwReg *)0x43000C08UL) /**< \brief (SERCOM7) I2CS Control C */ #define REG_SERCOM7_I2CS_INTENCLR (*(RwReg8 *)0x43000C14UL) /**< \brief (SERCOM7) I2CS Interrupt Enable Clear */ #define REG_SERCOM7_I2CS_INTENSET (*(RwReg8 *)0x43000C16UL) /**< \brief (SERCOM7) I2CS Interrupt Enable Set */ #define REG_SERCOM7_I2CS_INTFLAG (*(RwReg8 *)0x43000C18UL) /**< \brief (SERCOM7) I2CS Interrupt Flag Status and Clear */ #define REG_SERCOM7_I2CS_STATUS (*(RwReg16*)0x43000C1AUL) /**< \brief (SERCOM7) I2CS Status */ #define REG_SERCOM7_I2CS_SYNCBUSY (*(RoReg *)0x43000C1CUL) /**< \brief (SERCOM7) I2CS Synchronization Busy */ #define REG_SERCOM7_I2CS_LENGTH (*(RwReg16*)0x43000C22UL) /**< \brief (SERCOM7) I2CS Length */ #define REG_SERCOM7_I2CS_ADDR (*(RwReg *)0x43000C24UL) /**< \brief (SERCOM7) I2CS Address */ #define REG_SERCOM7_I2CS_DATA (*(RwReg *)0x43000C28UL) /**< \brief (SERCOM7) I2CS Data */ #define REG_SERCOM7_SPI_CTRLA (*(RwReg *)0x43000C00UL) /**< \brief (SERCOM7) SPI Control A */ #define REG_SERCOM7_SPI_CTRLB (*(RwReg *)0x43000C04UL) /**< \brief (SERCOM7) SPI Control B */ #define REG_SERCOM7_SPI_CTRLC (*(RwReg *)0x43000C08UL) /**< \brief (SERCOM7) SPI Control C */ #define REG_SERCOM7_SPI_BAUD (*(RwReg8 *)0x43000C0CUL) /**< \brief (SERCOM7) SPI Baud Rate */ #define REG_SERCOM7_SPI_INTENCLR (*(RwReg8 *)0x43000C14UL) /**< \brief (SERCOM7) SPI Interrupt Enable Clear */ #define REG_SERCOM7_SPI_INTENSET (*(RwReg8 *)0x43000C16UL) /**< \brief (SERCOM7) SPI Interrupt Enable Set */ #define REG_SERCOM7_SPI_INTFLAG (*(RwReg8 *)0x43000C18UL) /**< \brief (SERCOM7) SPI Interrupt Flag Status and Clear */ #define REG_SERCOM7_SPI_STATUS (*(RwReg16*)0x43000C1AUL) /**< \brief (SERCOM7) SPI Status */ #define REG_SERCOM7_SPI_SYNCBUSY (*(RoReg *)0x43000C1CUL) /**< \brief (SERCOM7) SPI Synchronization Busy */ #define REG_SERCOM7_SPI_LENGTH (*(RwReg16*)0x43000C22UL) /**< \brief (SERCOM7) SPI Length */ #define REG_SERCOM7_SPI_ADDR (*(RwReg *)0x43000C24UL) /**< \brief (SERCOM7) SPI Address */ #define REG_SERCOM7_SPI_DATA (*(RwReg *)0x43000C28UL) /**< \brief (SERCOM7) SPI Data */ #define REG_SERCOM7_SPI_DBGCTRL (*(RwReg8 *)0x43000C30UL) /**< \brief (SERCOM7) SPI Debug Control */ #define REG_SERCOM7_USART_CTRLA (*(RwReg *)0x43000C00UL) /**< \brief (SERCOM7) USART Control A */ #define REG_SERCOM7_USART_CTRLB (*(RwReg *)0x43000C04UL) /**< \brief (SERCOM7) USART Control B */ #define REG_SERCOM7_USART_CTRLC (*(RwReg *)0x43000C08UL) /**< \brief (SERCOM7) USART Control C */ #define REG_SERCOM7_USART_BAUD (*(RwReg16*)0x43000C0CUL) /**< \brief (SERCOM7) USART Baud Rate */ #define REG_SERCOM7_USART_RXPL (*(RwReg8 *)0x43000C0EUL) /**< \brief (SERCOM7) USART Receive Pulse Length */ #define REG_SERCOM7_USART_INTENCLR (*(RwReg8 *)0x43000C14UL) /**< \brief (SERCOM7) USART Interrupt Enable Clear */ #define REG_SERCOM7_USART_INTENSET (*(RwReg8 *)0x43000C16UL) /**< \brief (SERCOM7) USART Interrupt Enable Set */ #define REG_SERCOM7_USART_INTFLAG (*(RwReg8 *)0x43000C18UL) /**< \brief (SERCOM7) USART Interrupt Flag Status and Clear */ #define REG_SERCOM7_USART_STATUS (*(RwReg16*)0x43000C1AUL) /**< \brief (SERCOM7) USART Status */ #define REG_SERCOM7_USART_SYNCBUSY (*(RoReg *)0x43000C1CUL) /**< \brief (SERCOM7) USART Synchronization Busy */ #define REG_SERCOM7_USART_RXERRCNT (*(RoReg8 *)0x43000C20UL) /**< \brief (SERCOM7) USART Receive Error Count */ #define REG_SERCOM7_USART_LENGTH (*(RwReg16*)0x43000C22UL) /**< \brief (SERCOM7) USART Length */ #define REG_SERCOM7_USART_DATA (*(RwReg *)0x43000C28UL) /**< \brief (SERCOM7) USART Data */ #define REG_SERCOM7_USART_DBGCTRL (*(RwReg8 *)0x43000C30UL) /**< \brief (SERCOM7) USART Debug Control */ #endif /* (defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ /* ========== Instance parameters for SERCOM7 peripheral ========== */ #define SERCOM7_CLK_REDUCTION 1 // Reduce clock options to pin 1 for SPI and USART #define SERCOM7_DLY_COMPENSATION 1 // Compensates for a fast DLY50 element. Assuming 20ns #define SERCOM7_DMA 1 // DMA support implemented? #define SERCOM7_DMAC_ID_RX 18 // Index of DMA RX trigger #define SERCOM7_DMAC_ID_TX 19 // Index of DMA TX trigger #define SERCOM7_FIFO_DEPTH_POWER 1 // 2^FIFO_DEPTH_POWER gives rx FIFO depth. #define SERCOM7_GCLK_ID_CORE 37 #define SERCOM7_GCLK_ID_SLOW 3 #define SERCOM7_INT_MSB 6 #define SERCOM7_PMSB 3 #define SERCOM7_RETENTION_SUPPORT 0 // Retention supported? #define SERCOM7_SE_CNT 1 // SE counter included? #define SERCOM7_SPI 1 // SPI mode implemented? #define SERCOM7_SPI_HW_SS_CTRL 1 // Master _SS hardware control implemented? #define SERCOM7_SPI_ICSPACE_EXT 1 // SPI inter character space implemented? #define SERCOM7_SPI_OZMO 0 // OZMO features implemented? #define SERCOM7_SPI_WAKE_ON_SSL 1 // _SS low detect implemented? #define SERCOM7_TTBIT_EXTENSION 1 // 32-bit extension implemented? #define SERCOM7_TWIM 1 // TWI Master mode implemented? #define SERCOM7_TWIS 1 // TWI Slave mode implemented? #define SERCOM7_TWIS_AUTO_ACK 1 // TWI slave automatic acknowledge implemented? #define SERCOM7_TWIS_GROUP_CMD 1 // TWI slave group command implemented? #define SERCOM7_TWIS_SDASETUP_CNT_SIZE 8 // TWIS sda setup count size #define SERCOM7_TWIS_SDASETUP_SIZE 4 // TWIS sda setup size #define SERCOM7_TWIS_SUDAT 1 // TWI slave SDA setup implemented? #define SERCOM7_TWI_FASTMP 1 // TWI fast mode plus implemented? #define SERCOM7_TWI_HSMODE 1 // USART mode implemented? #define SERCOM7_TWI_SCLSM_MODE 1 // TWI SCL clock stretch mode implemented? #define SERCOM7_TWI_SMB_TIMEOUTS 1 // TWI SMBus timeouts implemented? #define SERCOM7_TWI_TENBIT_ADR 1 // TWI ten bit enabled? #define SERCOM7_USART 1 // USART mode implemented? #define SERCOM7_USART_AUTOBAUD 1 // USART autobaud implemented? #define SERCOM7_USART_COLDET 1 // USART collision detection implemented? #define SERCOM7_USART_FLOW_CTRL 1 // USART flow control implemented? #define SERCOM7_USART_FRAC_BAUD 1 // USART fractional BAUD implemented? #define SERCOM7_USART_IRDA 1 // USART IrDA implemented? #define SERCOM7_USART_ISO7816 1 // USART ISO7816 mode implemented? #define SERCOM7_USART_LIN_MASTER 1 // USART LIN Master mode implemented? #define SERCOM7_USART_RS485 1 // USART RS485 mode implemented? #define SERCOM7_USART_SAMPA_EXT 1 // USART sample adjust implemented? #define SERCOM7_USART_SAMPR_EXT 1 // USART oversampling adjustment implemented? #endif /* _SAME54_SERCOM7_INSTANCE_ */