Command echo .MESSAGE Parameters echo Echo a message back to the vty .MESSAGE The message to echo

Command enable Parameters enable Turn on privileged mode command

Command exit Parameters exit Exit current mode and down to previous mode

Command help Parameters help Description of the interactive help system

Command list Parameters list Print command list

Command logging color (0|1) Parameters logging Configure log message to this terminal color Configure color-printing for log messages 0 Don't use color for printing messages 1 Use color for printing messages

Command logging disable Parameters logging Configure log message to this terminal disable Disables logging to this vty

This command is required to make logging commands available on the telnet VTY. Command logging enable Parameters logging Configure log message to this terminal enable Enables logging to this vty

Disable/enable general log output on a given target. Typically, 'logging filter all 1' allows to see the usual log output on a given target. Setting to '0' can be useful when logging to the telnet VTY console: mute all log output to allow typing VTY commands on the telnet prompt without interference from log output; 'logging filter all 1' then re-enables logging in the same log output configuration as before. Some applications provide more specific filters, e.g. to log a given IMSI only. To employ such filters, set 'logging filter all 0' to disable general logging, and then enable a more specific filter instead. Command logging filter all (0|1) Parameters logging Configure log message to this terminal filter Filter log messages all Do you want to log all messages? 0 Only print messages matched by other filters 1 Bypass filter and print all messages

Command logging level (all|rll|cc|mm|rr|rsl|nm|mncc|pag|meas|sccp|msc|mgcp|ho|db|ref|gprs|ns|bssgp|llc|sndcp|nat|ctrl|smpp|lglobal|llapd|linp|lmux|lmi|lmib|lsms) (everything|debug|info|notice|error|fatal) Parameters logging Configure log message to this terminal level Set the log level for a specified category all Global setting for all subsystems rll A-bis Radio Link Layer (RLL) cc Layer3 Call Control (CC) mm Layer3 Mobility Management (MM) rr Layer3 Radio Resource (RR) rsl A-bis Radio Siganlling Link (RSL) nm A-bis Network Management / O&M (NM/OML) mncc MNCC API for Call Control application pag Paging Subsystem meas Radio Measurement Processing sccp SCCP Protocol msc Mobile Switching Center mgcp Media Gateway Control Protocol ho Hand-Over db Database Layer ref Reference Counting gprs GPRS Packet Service ns GPRS Network Service (NS) bssgp GPRS BSS Gateway Protocol (BSSGP) llc GPRS Logical Link Control Protocol (LLC) sndcp GPRS Sub-Network Dependent Control Protocol (SNDCP) nat GSM 08.08 NAT/Multiplexer ctrl Control interface smpp SMPP interface for external SMS apps lglobal Library-internal global log family llapd LAPD in libosmogsm linp A-bis Intput Subsystem lmux A-bis B-Subchannel TRAU Frame Multiplex lmi A-bis Input Driver for Signalling lmib A-bis Input Driver for B-Channels (voice) lsms Layer3 Short Message Service (SMS) everything Log simply everything debug Log debug messages and higher levels info Log informational messages and higher levels notice Log noticable messages and higher levels error Log error messages and higher levels fatal Log only fatal messages

Command logging set log mask MASK Parameters logging Configure log message to this terminal set Decide which categories to output. log Log commands mask Mask commands MASK The logmask to use

Command logging set-log-mask MASK Parameters logging Configure log message to this terminal set-log-mask Set the logmask of this logging target MASK The logmask to use

Command logging timestamp (0|1) Parameters logging Configure log message to this terminal timestamp Configure log message timestamping 0 Don't prefix each log message 1 Prefix each log message with current timestamp

Command show alarms Parameters show Show running system information alarms Show current logging configuration

Command show history Parameters show Show running system information history Display the session command history

Command show logging vty Parameters show Show running system information logging Show current logging configuration vty Show current logging configuration for this vty

Command show mgcp [stats] Parameters show Show running system information mgcp Display information about the MGCP Media Gateway [stats] Include Statistics

Command show online-help Parameters show Show running system information online-help Online help

Command show version Parameters show Show running system information version Displays program version

Command terminal length <0-512> Parameters terminal Set terminal line parameters length Set number of lines on a screen <0-512> Number of lines on screen (0 for no pausing)

Command terminal no length Parameters terminal Set terminal line parameters no Negate a command or set its defaults length Set number of lines on a screen

Command who Parameters who Display who is on vty

Command configure terminal Parameters configure Configuration from vty interface terminal Configuration terminal

Command copy running-config startup-config Parameters copy Copy configuration running-config Copy running config to... startup-config Copy running config to startup config (same as write file)

Command disable Parameters disable Turn off privileged mode command

Command echo .MESSAGE Parameters echo Echo a message back to the vty .MESSAGE The message to echo

Command exit Parameters exit Exit current mode and down to previous mode

Command free-endpoint <0-64> NUMBER Parameters free-endpoint Free the given endpoint <0-64> Trunk number NUMBER Endpoint number in hex.

Command help Parameters help Description of the interactive help system

Command list Parameters list Print command list

Command logging color (0|1) Parameters logging Configure log message to this terminal color Configure color-printing for log messages 0 Don't use color for printing messages 1 Use color for printing messages

Command logging disable Parameters logging Configure log message to this terminal disable Disables logging to this vty

This command is required to make logging commands available on the telnet VTY. Command logging enable Parameters logging Configure log message to this terminal enable Enables logging to this vty

Disable/enable general log output on a given target. Typically, 'logging filter all 1' allows to see the usual log output on a given target. Setting to '0' can be useful when logging to the telnet VTY console: mute all log output to allow typing VTY commands on the telnet prompt without interference from log output; 'logging filter all 1' then re-enables logging in the same log output configuration as before. Some applications provide more specific filters, e.g. to log a given IMSI only. To employ such filters, set 'logging filter all 0' to disable general logging, and then enable a more specific filter instead. Command logging filter all (0|1) Parameters logging Configure log message to this terminal filter Filter log messages all Do you want to log all messages? 0 Only print messages matched by other filters 1 Bypass filter and print all messages

Command logging level (all|rll|cc|mm|rr|rsl|nm|mncc|pag|meas|sccp|msc|mgcp|ho|db|ref|gprs|ns|bssgp|llc|sndcp|nat|ctrl|smpp|lglobal|llapd|linp|lmux|lmi|lmib|lsms) (everything|debug|info|notice|error|fatal) Parameters logging Configure log message to this terminal level Set the log level for a specified category all Global setting for all subsystems rll A-bis Radio Link Layer (RLL) cc Layer3 Call Control (CC) mm Layer3 Mobility Management (MM) rr Layer3 Radio Resource (RR) rsl A-bis Radio Siganlling Link (RSL) nm A-bis Network Management / O&M (NM/OML) mncc MNCC API for Call Control application pag Paging Subsystem meas Radio Measurement Processing sccp SCCP Protocol msc Mobile Switching Center mgcp Media Gateway Control Protocol ho Hand-Over db Database Layer ref Reference Counting gprs GPRS Packet Service ns GPRS Network Service (NS) bssgp GPRS BSS Gateway Protocol (BSSGP) llc GPRS Logical Link Control Protocol (LLC) sndcp GPRS Sub-Network Dependent Control Protocol (SNDCP) nat GSM 08.08 NAT/Multiplexer ctrl Control interface smpp SMPP interface for external SMS apps lglobal Library-internal global log family llapd LAPD in libosmogsm linp A-bis Intput Subsystem lmux A-bis B-Subchannel TRAU Frame Multiplex lmi A-bis Input Driver for Signalling lmib A-bis Input Driver for B-Channels (voice) lsms Layer3 Short Message Service (SMS) everything Log simply everything debug Log debug messages and higher levels info Log informational messages and higher levels notice Log noticable messages and higher levels error Log error messages and higher levels fatal Log only fatal messages

Command logging set log mask MASK Parameters logging Configure log message to this terminal set Decide which categories to output. log Log commands mask Mask commands MASK The logmask to use

Command logging set-log-mask MASK Parameters logging Configure log message to this terminal set-log-mask Set the logmask of this logging target MASK The logmask to use

Command logging timestamp (0|1) Parameters logging Configure log message to this terminal timestamp Configure log message timestamping 0 Don't prefix each log message 1 Prefix each log message with current timestamp

Command loop-endpoint <0-64> NAME (0|1) Parameters loop-endpoint Loop a given endpoint <0-64> Trunk number NAME The name in hex of the endpoint 0 Disable the loop 1 Enable the loop

Command reset-all-endpoints Parameters reset-all-endpoints Reset all endpoints

Command reset-endpoint <0-64> NUMBER Parameters reset-endpoint Reset the given endpoint <0-64> Trunk number NUMBER Endpoint number in hex.

Command show alarms Parameters show Show running system information alarms Show current logging configuration

Command show history Parameters show Show running system information history Display the session command history

Command show logging vty Parameters show Show running system information logging Show current logging configuration vty Show current logging configuration for this vty

Command show mgcp [stats] Parameters show Show running system information mgcp Display information about the MGCP Media Gateway [stats] Include Statistics

Command show online-help Parameters show Show running system information online-help Online help

Command show running-config Parameters show Show running system information running-config running configuration

Command show startup-config Parameters show Show running system information startup-config Contentes of startup configuration

Command show version Parameters show Show running system information version Displays program version

Command tap-call <0-64> ENDPOINT (bts-in|bts-out|net-in|net-out) A.B.C.D <0-65534> Parameters tap-call Forward data on endpoint to a different system <0-64> Trunk number ENDPOINT The endpoint in hex bts-in Forward the data coming from the bts bts-out Forward the data coming from the bts leaving to the network net-in Forward the data coming from the net net-out Forward the data coming from the net leaving to the bts A.B.C.D destination IP of the data <0-65534> destination port

Command terminal length <0-512> Parameters terminal Set terminal line parameters length Set number of lines on a screen <0-512> Number of lines on screen (0 for no pausing)

Command terminal monitor Parameters terminal Set terminal line parameters monitor Copy debug output to the current terminal line

Command terminal no length Parameters terminal Set terminal line parameters no Negate a command or set its defaults length Set number of lines on a screen

Command terminal no monitor Parameters terminal Set terminal line parameters no Negate a command or set its defaults monitor Copy debug output to the current terminal line

Command who Parameters who Display who is on vty

Command write Parameters write Write running configuration to memory, network, or terminal

Command write file Parameters write Write running configuration to memory, network, or terminal file Write to configuration file

Command write memory Parameters write Write running configuration to memory, network, or terminal memory Write configuration to the file (same as write file)

Command write terminal Parameters write Write running configuration to memory, network, or terminal terminal Write to terminal

Command banner motd default Parameters banner Set banner string motd Strings for motd default Default string

Command banner motd file [FILE] Parameters banner Set banner motd Banner for motd file Banner from a file [FILE] Filename

Command enable password (8|) WORD Parameters enable Modify enable password parameters password Assign the privileged level password 8 Specifies a HIDDEN password will follow dummy string WORD The HIDDEN 'enable' password string

Command enable password LINE Parameters enable Modify enable password parameters password Assign the privileged level password LINE The UNENCRYPTED (cleartext) 'enable' password

Command end Parameters end End current mode and change to enable mode.

Command exit Parameters exit Exit current mode and down to previous mode

Command help Parameters help Description of the interactive help system

Command hostname WORD Parameters hostname Set system's network name WORD This system's network name

Command line vty Parameters line Configure a terminal line vty Virtual terminal

Command list Parameters list Print command list

Command log alarms <2-32700> Parameters log Configure logging sub-system alarms Logging alarms to osmo_strrb <2-32700> Maximum number of messages to log

Command log file .FILENAME Parameters log Configure logging sub-system file Logging to text file .FILENAME Filename

Command log stderr Parameters log Configure logging sub-system stderr Logging via STDERR of the process

Command log syslog (authpriv|cron|daemon|ftp|lpr|mail|news|user|uucp) Parameters log Configure logging sub-system syslog Logging via syslog authpriv Security/authorization messages facility cron Clock daemon (cron/at) facility daemon General system daemon facility ftp Ftp daemon facility lpr Line printer facility mail Mail facility news News facility user Generic facility uucp UUCP facility

Command log syslog local <0-7> Parameters log Configure logging sub-system syslog Logging via syslog local Syslog LOCAL facility <0-7> Local facility number

Command mgcp Parameters mgcp Configure the MGCP

Command no banner motd Parameters no Negate a command or set its defaults banner Set banner string motd Strings for motd

Command no enable password Parameters no Negate a command or set its defaults enable Modify enable password parameters password Assign the privileged level password

Command no hostname [HOSTNAME] Parameters no Negate a command or set its defaults hostname Reset system's network name [HOSTNAME] Host name of this router

Command no log alarms Parameters no Negate a command or set its defaults log Configure logging sub-system alarms Logging alarms to osmo_strrb

Command no log file .FILENAME Parameters no Negate a command or set its defaults log Configure logging sub-system file Logging to text file .FILENAME Filename

Command no log stderr Parameters no Negate a command or set its defaults log Configure logging sub-system stderr Logging via STDERR of the process

Command no log syslog Parameters no Negate a command or set its defaults log Configure logging sub-system syslog Logging via syslog

Command no service advanced-vty Parameters no Negate a command or set its defaults service Set up miscellaneous service advanced-vty Enable advanced mode vty interface

Command no service terminal-length [<0-512>] Parameters no Negate a command or set its defaults service Set up miscellaneous service terminal-length System wide terminal length configuration [<0-512>] Number of lines of VTY (0 means no line control)

Command password (8|) WORD Parameters password Assign the terminal connection password 8 Specifies a HIDDEN password will follow dummy string WORD The HIDDEN line password string

Command password LINE Parameters password Assign the terminal connection password LINE The UNENCRYPTED (cleartext) line password

Command service advanced-vty Parameters service Set up miscellaneous service advanced-vty Enable advanced mode vty interface

Command service terminal-length <0-512> Parameters service Set up miscellaneous service terminal-length System wide terminal length configuration <0-512> Number of lines of VTY (0 means no line control)

Command show history Parameters show Show running system information history Display the session command history

Command show running-config Parameters show Show running system information running-config running configuration

Command write Parameters write Write running configuration to memory, network, or terminal

Command write file Parameters write Write running configuration to memory, network, or terminal file Write to configuration file

Command write memory Parameters write Write running configuration to memory, network, or terminal memory Write configuration to the file (same as write file)

Command write terminal Parameters write Write running configuration to memory, network, or terminal terminal Write to terminal

Command end Parameters end End current mode and change to enable mode.

Command exit Parameters exit Exit current mode and down to previous mode

Command help Parameters help Description of the interactive help system

Command list Parameters list Print command list

Command logging color (0|1) Parameters logging Configure log message to this terminal color Configure color-printing for log messages 0 Don't use color for printing messages 1 Use color for printing messages

Disable/enable general log output on a given target. Typically, 'logging filter all 1' allows to see the usual log output on a given target. Setting to '0' can be useful when logging to the telnet VTY console: mute all log output to allow typing VTY commands on the telnet prompt without interference from log output; 'logging filter all 1' then re-enables logging in the same log output configuration as before. Some applications provide more specific filters, e.g. to log a given IMSI only. To employ such filters, set 'logging filter all 0' to disable general logging, and then enable a more specific filter instead. Command logging filter all (0|1) Parameters logging Configure log message to this terminal filter Filter log messages all Do you want to log all messages? 0 Only print messages matched by other filters 1 Bypass filter and print all messages

Command logging level (all|rll|cc|mm|rr|rsl|nm|mncc|pag|meas|sccp|msc|mgcp|ho|db|ref|gprs|ns|bssgp|llc|sndcp|nat|ctrl|smpp|lglobal|llapd|linp|lmux|lmi|lmib|lsms) (everything|debug|info|notice|error|fatal) Parameters logging Configure log message to this terminal level Set the log level for a specified category all Global setting for all subsystems rll A-bis Radio Link Layer (RLL) cc Layer3 Call Control (CC) mm Layer3 Mobility Management (MM) rr Layer3 Radio Resource (RR) rsl A-bis Radio Siganlling Link (RSL) nm A-bis Network Management / O&M (NM/OML) mncc MNCC API for Call Control application pag Paging Subsystem meas Radio Measurement Processing sccp SCCP Protocol msc Mobile Switching Center mgcp Media Gateway Control Protocol ho Hand-Over db Database Layer ref Reference Counting gprs GPRS Packet Service ns GPRS Network Service (NS) bssgp GPRS BSS Gateway Protocol (BSSGP) llc GPRS Logical Link Control Protocol (LLC) sndcp GPRS Sub-Network Dependent Control Protocol (SNDCP) nat GSM 08.08 NAT/Multiplexer ctrl Control interface smpp SMPP interface for external SMS apps lglobal Library-internal global log family llapd LAPD in libosmogsm linp A-bis Intput Subsystem lmux A-bis B-Subchannel TRAU Frame Multiplex lmi A-bis Input Driver for Signalling lmib A-bis Input Driver for B-Channels (voice) lsms Layer3 Short Message Service (SMS) everything Log simply everything debug Log debug messages and higher levels info Log informational messages and higher levels notice Log noticable messages and higher levels error Log error messages and higher levels fatal Log only fatal messages

Command logging timestamp (0|1) Parameters logging Configure log message to this terminal timestamp Configure log message timestamping 0 Don't prefix each log message 1 Prefix each log message with current timestamp

Command show running-config Parameters show Show running system information running-config running configuration

Command write Parameters write Write running configuration to memory, network, or terminal

Command write file Parameters write Write running configuration to memory, network, or terminal file Write to configuration file

Command write memory Parameters write Write running configuration to memory, network, or terminal memory Write configuration to the file (same as write file)

Command write terminal Parameters write Write running configuration to memory, network, or terminal terminal Write to terminal

This node allows to configure global MGCP settings. These include the various port numbers.

Command bind early (0|1) Parameters bind Listen/Bind related socket option early Bind local ports on start up 0 Bind on demand 1 Bind on startup

Command bind ip A.B.C.D Parameters bind Listen/Bind related socket option ip IP information A.B.C.D IPv4 Address to bind to

Command bind port <0-65534> Parameters bind Listen/Bind related socket option port Port information <0-65534> UDP port to listen for MGCP messages

Command bts ip A.B.C.D Parameters bts BTS Audio source/destination options ip IP information A.B.C.D IPv4 Address of the BTS

Command call agent ip A.B.C.D Parameters call Callagent information agent Callagent information ip IP information A.B.C.D IPv4 Address of the callagent

Command call-agent ip A.B.C.D Parameters call-agent Callagent information ip IP information A.B.C.D IPv4 Address of the callagent

Command end Parameters end End current mode and change to enable mode.

Command exit Parameters exit Exit current mode and down to previous mode

Command help Parameters help Description of the interactive help system

Command list Parameters list Print command list

Command local ip A.B.C.D Parameters local Local options for the SDP record ip IP information A.B.C.D IPv4 Address to use in SDP record

Command loop (0|1) Parameters loop Loop audio for all endpoints on main trunk 0 Don't Loop 1 Loop

Command no rtcp-omit Parameters no Negate a command or set its defaults rtcp-omit Drop RTCP packets in both directions

Command no rtp keep-alive Parameters no Negate a command or set its defaults rtp RTP configuration keep-alive Send dummy UDP packet to net RTP destination

Command no rtp-patch Parameters no Negate a command or set its defaults rtp-patch Modify RTP packet header in both directions

Command no rtp-patch ssrc Parameters no Negate a command or set its defaults rtp-patch Modify RTP packet header in both directions ssrc Force a fixed SSRC

Command no rtp-patch timestamp Parameters no Negate a command or set its defaults rtp-patch Modify RTP packet header in both directions timestamp Adjust RTP timestamp

Command no sdp audio-payload send-ptime Parameters no Negate a command or set its defaults sdp SDP File related options audio-payload Audio payload options send-ptime Send SDP ptime (packet duration) attribute

Command no transcoder-mgw Parameters no Negate a command or set its defaults transcoder-mgw Disable the transcoding

Command number endpoints <0-65534> Parameters number Number options endpoints Endpoints available <0-65534> Number endpoints

Command rtcp-omit Parameters rtcp-omit Drop RTCP packets in both directions

Command rtp base <0-65534> Parameters rtp RTP configuration base First UDP port allocated for the BTS side <0-65534> UDP Port number

Command rtp bts-base <0-65534> Parameters rtp RTP configuration bts-base First UDP port allocated for the BTS side <0-65534> UDP Port number

Command rtp bts-range <0-65534> <0-65534> Parameters rtp RTP configuration bts-range Range of ports to use for the BTS side <0-65534> Start of the range of ports <0-65534> End of the range of ports

Command rtp ip-dscp <0-255> Parameters rtp RTP configuration ip-dscp Apply IP_TOS to the audio stream <0-255> The DSCP value

Command rtp ip-tos <0-255> Parameters rtp RTP configuration ip-tos Apply IP_TOS to the audio stream <0-255> The DSCP value

Command rtp keep-alive <1-120> Parameters rtp RTP configuration keep-alive Send dummy UDP packet to net RTP destination <1-120> Keep alive interval in secs

Command rtp keep-alive once Parameters rtp RTP configuration keep-alive Send dummy UDP packet to net RTP destination once Send dummy packet only once after CRCX/MDCX

Command rtp net-base <0-65534> Parameters rtp RTP configuration net-base First UDP port allocated for the NET side <0-65534> UDP Port number

Command rtp net-range <0-65534> <0-65534> Parameters rtp RTP configuration net-range Range of ports to use for the NET side <0-65534> Start of the range of ports <0-65534> End of the range of ports

Command rtp transcoder-base <0-65534> Parameters rtp RTP configuration transcoder-base First UDP port allocated for the Transcoder side <0-65534> UDP Port number

Command rtp transcoder-range <0-65534> <0-65534> Parameters rtp RTP configuration transcoder-range Range of ports to use for the Transcoder <0-65534> Start of the range of ports <0-65534> End of the range of ports

Command rtp-patch ssrc Parameters rtp-patch Modify RTP packet header in both directions ssrc Force a fixed SSRC

Command rtp-patch timestamp Parameters rtp-patch Modify RTP packet header in both directions timestamp Adjust RTP timestamp

Command sdp audio fmtp-extra .NAME Parameters sdp Add extra fmtp for the SDP file audio Audio fmtp-extra Fmtp-extra .NAME Extra Information

Command sdp audio payload name NAME Parameters sdp SDP File related options audio Audio payload options payload Audio payload options name Name NAME Payload name

Command sdp audio payload number <1-255> Parameters sdp SDP File related options audio Audio payload options payload Audio payload options number Number <1-255> Payload number

Command sdp audio-payload name NAME Parameters sdp SDP File related options audio-payload Audio payload options name Name NAME Payload name

Command sdp audio-payload number <1-255> Parameters sdp SDP File related options audio-payload Audio payload options number Number <1-255> Payload number

Command sdp audio-payload send-ptime Parameters sdp SDP File related options audio-payload Audio payload options send-ptime Send SDP ptime (packet duration) attribute

Command show running-config Parameters show Show running system information running-config running configuration

Command transcoder-mgw A.B.C.D Parameters transcoder-mgw Use a MGW to detranscoder RTP A.B.C.D The IP address of the MGW

Command transcoder-remote-base <0-65534> Parameters transcoder-remote-base Set the base port for the transcoder <0-65534> The RTP base port on the transcoder

Command trunk <1-64> Parameters trunk Configure a SS7 trunk <1-64> Trunk Nr

Command write Parameters write Write running configuration to memory, network, or terminal

Command write file Parameters write Write running configuration to memory, network, or terminal file Write to configuration file

Command write memory Parameters write Write running configuration to memory, network, or terminal memory Write configuration to the file (same as write file)

Command write terminal Parameters write Write running configuration to memory, network, or terminal terminal Write to terminal

This node allows to configure a MGCP trunk. These include the number, the local binding ports, SDP configuration.

Command end Parameters end End current mode and change to enable mode.

Command exit Parameters exit Exit current mode and down to previous mode

Command help Parameters help Description of the interactive help system

Command list Parameters list Print command list

Command loop (0|1) Parameters loop Loop audio for all endpoints on this trunk 0 Don't Loop 1 Loop

Command no rtcp-omit Parameters no Negate a command or set its defaults rtcp-omit Drop RTCP packets in both directions

Command no rtp keep-alive Parameters no Negate a command or set its defaults rtp RTP configuration keep-alive Send dummy UDP packet to net RTP destination

Command no rtp-patch Parameters no Negate a command or set its defaults rtp-patch Modify RTP packet header in both directions

Command no rtp-patch ssrc Parameters no Negate a command or set its defaults rtp-patch Modify RTP packet header in both directions ssrc Force a fixed SSRC

Command no rtp-patch timestamp Parameters no Negate a command or set its defaults rtp-patch Modify RTP packet header in both directions timestamp Adjust RTP timestamp

Command no sdp audio-payload send-ptime Parameters no Negate a command or set its defaults sdp SDP File related options audio-payload Audio payload options send-ptime Send SDP ptime (packet duration) attribute

Command rtcp-omit Parameters rtcp-omit Drop RTCP packets in both directions

Command rtp keep-alive <1-120> Parameters rtp RTP configuration keep-alive Send dummy UDP packet to net RTP destination <1-120> Keep-alive interval in secs

Command rtp keep-alive once Parameters rtp RTP configuration keep-alive Send dummy UDP packet to net RTP destination once Send dummy packet only once after CRCX/MDCX

Command rtp-patch ssrc Parameters rtp-patch Modify RTP packet header in both directions ssrc Force a fixed SSRC

Command rtp-patch timestamp Parameters rtp-patch Modify RTP packet header in both directions timestamp Adjust RTP timestamp

Command sdp audio fmtp-extra .NAME Parameters sdp Add extra fmtp for the SDP file audio Audio fmtp-extra Fmtp-extra .NAME Extra Information

Command sdp audio payload name NAME Parameters sdp SDP File related options audio Audio payload options payload Audio payload options name Payload NAME Payload Name

Command sdp audio payload number <1-255> Parameters sdp SDP File related options audio Audio payload options payload Audio payload options number Number <1-255> Payload Number

Command sdp audio-payload name NAME Parameters sdp SDP File related options audio-payload Audio payload options name Payload NAME Payload Name

Command sdp audio-payload number <1-255> Parameters sdp SDP File related options audio-payload Audio payload options number Number <1-255> Payload Number

Command sdp audio-payload send-ptime Parameters sdp SDP File related options audio-payload Audio payload options send-ptime Send SDP ptime (packet duration) attribute

Command show running-config Parameters show Show running system information running-config running configuration

Command write Parameters write Write running configuration to memory, network, or terminal

Command write file Parameters write Write running configuration to memory, network, or terminal file Write to configuration file

Command write memory Parameters write Write running configuration to memory, network, or terminal memory Write configuration to the file (same as write file)

Command write terminal Parameters write Write running configuration to memory, network, or terminal terminal Write to terminal